Zelmer ZPG6014CP, Руководство пользователя

Страница: 37 / 40

37
PG-004_v01
Gas and electrical connections
THE MANUFACTURER DOES NOT BEAR ANY
RESPONSIBILITY FOR POSSIBLE DAMAGED
CAUSED BY NON- OBSERVANCE OF STANDARDS
AND REGULATIONS IN FORCE AS WELL AS HOB
CONNECTION EXECUTED BY NOT AUTHORISED
PERSON.
REMARK: Connection of the hob both to electrical and
gas fi tting can be executed by quali fi ed authorised
installer only.
Before connecting the hob to the electrical and gas
fi tting check the information on the nameplate and
herewith manual.
Before installing make sure that the local distribution
●
conditions (the type of gas, its pressure) and the
appliance adjustment are compliant.
The conditions of gas adjustment of the appliance are
●
indicated on the nameplate.
The appliance is not connected to the fumes conduits.
●
It should be installed and connected according to
the binding installation regulations. The appropriate
requirements concerning ventilation should be taken into
consideration.
The
fl exible gas connection shall be assembled such
●
way, that it is not in contact with the furniture parts in
move (i.e. drawer) and it shall be not located in the are
with not enough space.
The wiring supplying the power to the hob shall be
●
secured with properly selected safety device.
Upon installing the hob, the installer is obliged to check
●
the tightness of the gas fi tting.
REMARK: The installer is obliged to fi ll in the warranty
card, which is the basis for the warranty and guaranty.
Replacing the nozzles for the other
type of gas
(Fig. B)
ATTENTION: The hob nozzles replacing can be
executed only by an authorised quali fi ed installer.
The gas hob is the nozzles are defaulted for 2E (G20) gas.
The other kinds of gas are:
BURNER GAS PRESSURE NOZZLE
MARKING
THERMAL
CAPACITY
WOK
2E (G20)
3B/P (G30)
20 mbar
37 mbar
1.36
0.86
3300 W
LARGE
2E (G20)
3B/P (G30)
20 mbar
37 mbar
1.18
0.72
2500 W
MEDIUM
2E (G20)
3B/P (G30)
20 mbar
37 mbar
0.92
0.58
1500 W
SMALL
2E (G20)
3B/P (G30)
20 mbar
37 mbar
0.75
0.49
1000 W
1
Remove the cap and crown.
2
Unscrew the nozzle using a special spanner.
3
Replace the nozzle screwing the appropriate one
according to the table.
After the nozzles exchange adjust the burners (see
”FLAME ADJUSTMENT”.
Upon nozzles replacement glue an adequate label
indicating the gas type near the end of shaft connecting
the hob manifold.
Technical specifi cation
The technical parameters of the hob are indicated at the
nameplate of the appliance.
The hob is equipped with a shaft with threaded end of G1/2”
diameter for connecting to gas supply fi tting. In case of
connection to LPG cylinder (propane –butane) the ending
of the fl exible hose
∅
8 x 1mm is screwed on the threaded
shaft end.
The gas hob is the 1st class appliance equipped with
a connecting cord with protecting stand. It requires
connection to the socket equipped with an earth pin.
the appliance meets the requirements of the standards in
force.
The appliance is in conformance with the requirements of the
following directives:
Appliances burning gaseous fuels – 90/396/EEC, –
93/68/EEC.
Low Voltage Devices (LVD) – 2006/95/EC. –
Electromagnetic compatibility (EMC) – 2004/108/EC. –
The product has been labelled with CE mark on the
nameplate.
The appliance outline (Fig. D)
1
Large burner Ø 100 mm 2.5 kW
2
Medium burner Ø 75 mm 1.5 kW
3
Small burner Ø 55 mm 1.0 kW
4
WOK burner Ø 130 mm 3.3 kW
5
Burner control knobs with electric ignition candle
6
Burner grate
7
Burner cap
8
Burner crown
9
Burner body
10
Ignition candle
11
Anti-gas fl ow security device
Flame adjusting (Fig. C)
1
Switch on the burner and set the minimum fl ame .
2
Remove the ring knob from the spindle.
3
Adjust the fl ame turning the screw inside the spindle with
an appropriate screwdriver.