Zelmer ZCK1174X, Руководство пользователя

Страница: 50 / 52

50
ZCK1174X-001_v03
Operating the kettle
1 Pull the lid release button (6) in the direction indicated by
the arrow. The kettle lid will open.
2 Place the filter (11) in the kettle (if it is not in place).
3
Fill the kettle with the desired amount of water (the level
is visible on the indicator (3) ).
Do not boil water if the water level is below the
MIN or above the MAX indicator (3).
4
Close the lid (5) .
5 Place the kettle on the base (4) . Plug the kettle to
a socket provided with an earth pin.
6 Switch on the kettle by pushing button (10) – the LCD
display (7) will turn blue and the icon will flash. After
some time the illumination will go out (the icon will keep
flashing). The kettle will switch off automatically after boiling.
7
The kettle has three functions:
boiling water , keep warm and boiling time . The
selected mode is displayed on the LCD display (7) . Functions
can be changed using the boiling program selection button
(8) . During boiling, the LCD display will turn blue, and the
icon of the selected function will appear on the display.
8
Default settings: boiling water to 100°C, the keep warm
function in on.
When setting boiling parameters, water temperature may
be adjusted from 40°C to 100°C (each time the button is
pressed the temperature changes by 5°C). The temperature
setting may be changed by pressing the settings buttons (9) .
The selected boiling temperature is shown on the LCD display.
9
When setting the keep warm temperature, water
temperature may be set between 40°C and 90°C, if the
previous temperature setting was 100°C. If boiling
temperature was set for example to 50°C, the keep warm
temperature may be set from 40°C to 50°C (each time the
button is pressed the temperature changes by 5°C). The
set temperature may be changed by pressing the settings
buttons (9) . The maximum duration of the keep warm
function is 60 minutes. In order to switch off the keep warm
function, set this parameter to “00”.
When the keep warm function is on, the kettle
boils water to the preset temperature (the
icon flashes) and then switches to the preset
keep warm temperature (the icon flashes).
10 Water boiling time can be set from 3 seconds to
6 seconds. The time is measured from the moment the water
starts to boil until the kettle automatically shuts down. You
can adjust the time by pressing settings buttons (9) .
This setting is effective only when the water
boiling temperature exceeds 95°C and the
kettle is filled with 1.7 l of water.
11 When finished programming the settings, press button
(10) . When in the operation mode, the operation function icon
B
flashes; the selected water temperature is shown on the LCD
display. When heating starts, a blue light comes on inside the
kettle. To go back to the settings mode, press button (10) button.
12
The appliance will switch off automatically after reaching
the set temperature. The light will go out.
During boiling or when the keep warm function
is on, if you lift the kettle off the base and put
it back on, all previous settings will be reset.
The appliance will automatically go back to
default settings (see
B
8
). To use the boiling
function or the keep warm function, select an
appropriate program again.
If water cools down, switch on the kettle again
to boil or heat water again.
If you plan to use the kettle again soon, it is not necessary
to remove the plug from the mains.
Make sure that the maximum kettle capacity is
not exceeded when the kettle is filled with water.
In the event that an empty kettle is switched on,
it will be switched off automatically by a thermal
device. In order to switch on the kettle again
after it cools down (approx. 15 minutes), lift it off
the base, fill with water, put the kettle back on
the base and switch on by pressing button (10).
Do not fill a hot kettle with cold water (and the
other way around).
When filling the kettle, avoid high temperature
differences.
Cleaning and maintenance
Always allow the kettle to cool down completely
before cleaning!
1 Unplug the kettle from the mains.
2 Remove the filter (11) and rinse it under running water.
3 Clean the outside surfaces with a soft damp cloth and
washing-up liquid.
In order to remove the build-up of hard water film from the
outside and inside walls of the kettle, wipe them with a damp
cloth and vinegar.
4
Rinse the kettle with fresh water and assemble the
appliance only after all parts have been dried thoroughly.
Various black-coloured, rusty, milky, etc.
deposits may form inside the kettle and float on
the water. This is caused by minerals occurring
naturally in water (calcium, magnesium, iron,
etc.). Such discoloration is not caused by faulty
operation of the appliance and does not affect
its use. In case of substantial accumulation of
mineral deposits, proceed as described in the
“Descaling” section.
C