Zelmer Tiny VC1400, Руководство пользователя

Страница: 57 / 62

63
VC1400-001_v02
12 The vacuum cleaner is also equipped with a mechanic
suction power controller, which is situated on the hose
handle. You may use it to slightly regulate the suction power
without the need to use the dial.
Installing/deinstalling the CYKLON dust
container
The vacuum cleaner is equipped with a removable CYKLON
dust container (which is a removable part of the vacuum
cleaner) responsible for collecting dirt. After the CYKLON
dust container is full, it has to be emptied.
The vacuum cleaner is equipped with a safety
valve situated in the chamber of the vacuum
cleaner. It opens up automatically when the
suction hose or any elements attached to it are
completely clogged up, and when the CYKLON
dust container is overfilled. After the valve is
open, you will hear a characteristic fluttering in
the vacuum cleaner.
1
Press the on/off button (6) to stop the vacuum cleaner.
Remove the plug of the cord from the socket.
2 Turn the end of the suction hose counter-clockwise, and
remove the end of the hose from the inlet of the vacuum
cleaner.
3 Release the fastening of the upper cover (5) , and open it.
4 Remove the CYKLON dust container from the vacuum
cleaner. In order to do this hold the body of the vacuum
cleaner by one hand, grab the special handgrip situated on
the cover of the dust container by the other, and by holding
it like that gently remove the CYKLON dust container out of
the vacuum cleaner.
5 Pull the fastenings on the cover of the CYKLON dust
container aside, and remove the cover from the container.
6
Move the CYKLON dust container over a dustbin, and
empty its contents.
After doing this, check the HEPA H12 basic
filter, and clean or replace it, if necessary.
7
Place the cover of the CYKLON dust container on the
container in such a way that the fastening situated in the
front part of the cover is inserted into the projection of the
container. Press the back part of the cover in such a way that
the fastenings are shut tight on the body of the container.
The CYKLON dust container has to be shut
tight. Otherwise, the suction power of the
vacuum cleaner is going to drop.
8 Place the emptied CYKLON dust container into the
chamber of the vacuum cleaner. Close the upper cover of the
vacuum cleaner by pressing it, until you hear a characteristic
“click.”
It is necessary to empty the CYKLON dust container, if you
notice that:
a) the vacuum cleaner works less efficiently,
b) the CYKLON dust container is full.
C
Deinstalling the filters
The vacuum cleaner is equipped with the CYKLON dust
container based on cyclone filtration, making it possible to
use the vacuum cleaner without a dust bag. A cyclone filter
uses air stream swirling to separate solid dirt. Separation
of dirt is done in an O-shaped part of the container, where
the swirling air casts away dirt on the wall of the container,
and then through the hole into the adjacent chamber of the
container. This pre-filtered air is directed into the washable
HEPA H12 conical filter stopping the tiniest fractions of dust.
A special filtration material used in the washable HEPA H12
filter makes it possible to rinse the filter with running water, if
it is dirty, and reuse it later.
At the outlet of the vacuum cleaner there is a microfilter
installed.
In case the HEPA H12 basic filter (14) or the
outlet microfilter (13) are dirty, they can be
replaced with new ones, cleaned or rinsed with
running water.
It is forbidden to wash filters in washing
machines or dishwashers.
Filters may be dried only naturally.
Do not use hairdryers, heaters or radiators to
dry filters.
Before replacing the filters make sure the
vacuum cleaner is off, and the plug of the cord
is unplugged from the socket.
HEPA H12 BASIC FILTER
It is necessary to periodically clean the HEPA H12 basic filter
to remove small fractions of dust.
Remove the CYKLON dust container and empty it, as
described in para. C .
1 Pull the fastenings on the cover of the CYKLON dust
container aside, and remove the cover from the container.
If the CYKLON dust container is full, empty it as described in
para. C .
2 Remove the protective casing of the HEPA H12 basic
filter out of the dust container. In order to do this turn the
protective casing of the HEPA H12 basic filter in the direction
given on the symbol „ ” (it is situated along with an arrow
on the protective casing of the HEPA H12 basic filter).
Clean, wipe, and carefully dry the casing.
●
3 Remove the HEPA H12 basic filter from the container
Clean the pleats of the HEPA H12 basic filter
●
(14) , and
if the filter is damaged, it should be definitely replaced
with a new one. If the HEPA H12 basic filter (14) is dirty,
you may replace it with a new one, clean it or rinse it with
running water. Before reinstalling the filter, make sure it
is dry.
For safety reasons it is unacceptable to install
a wet or damaged HEPA H12 basic filter (14).
D