Zelmer Odyssey 450, Руководство пользователя

Страница: 47 / 50

51
B
Appliance elements
1 Electrobrush socket (type 450.0 EK, 450.0 SP, 450.0 ST)
2 ON/OFF button
3 Handle
4 Cord rewind button
5 Combination brush fastening
6 Plug and cord
7 Outlet filter cover
8 Front cover fastening
9 Suction power regulation slider
10 Accessory compartment cover
11 Suction hose. The vacuum cleaner is equipped with one
suction hose (A or B)
A Suction hose with a handle (type 450.0 EK, 450.0 SP,
450.0 ST)
B Suction hose (type 450.0 EH)
12 Suction pipe. The vacuum cleaner is equipped with one
kind of suction pipe (A or B)
A Telescopic suction tube (type 450.0 EK, 450.0 SP,
450.0 ST)
B
Segmented suction tubes (type 450.0 EH)
13 SAFBAG dust bag (2 pieces)
14 Outlet filter. The vacuum cleaner is equipped with only
one outlet filter (A or B)
A Outlet filter HEPA H11 (type 450.0 SP, 450.0 ST)
(installed in the vacuum cleaner)
B
“ACF Microfilter” outlet filter (type 450.0 EH,
450.0 EK) (installed in the vacuum cleaner)
15 Inlet filter (installed in the vacuum cleaner)
16 Small nozzle
17 Small brush
18 Crevice nozzle
19 Parquet brush “BNB” (type 450.0 SP, 450.0 ST)
Is used to clean and polish hard, scratch sensitive surfaces
such as wooden floors, floor panels, parquet, marble, tiles, etc.
Delicate and soft natural bristles ensure maximum vacuum
effectiveness and protects against scratching the cleaned
surface.
20 Switchable combination brush
21 Turbobrush (type 450.0 ST)
22 Electrobrush (additional equipment – may be bought in
retail centers)
Preparing the vacuum cleaner for
operation
1 Pull the end of the suction hose into the opening and
press lightly.
2 Attach the other end of the hose (the handle) to the
suction tube. In order to do this, press the lock A in the
telescopic suction tube and put the tube in the handle, so the
lock A is fastened in hole B .
3
Join both segments of the suction tube together.
4 In case of the telescopic suction tube adjust the
necessary tube length by moving the slider according to the
slide in/slide out direction arrow.
5 Assemble the appropriate nozzle or brush to the other
end of the suction tube.
6 To clean hard surfaces – wooden floors, plastic floors,
ceramic tiles etc. pull out the brush by pressing the switch on
the combination brush according to the figure .
7 The vacuum cleaner is equipped with an accessory
compartment. In order to open it pull the compartment cover
(10) up.
8 The accessories may be attached to the accessory holder
in the suction hose handle. This way they will be available for
use at any time (type 450.0 EK, 450.0 SP, 450.0 ST).
9 Pull the plug and cord (6) out of the vacuum cleaner.
ATTENTION! While pulling out the cord, pay attention
to the yellow stripe which signals the end of the
cord. Further attempts (pulling on cord) may result in
damaging the cord.
10 Plug in the appliance.
Before operation make sure that the SAFBAG bag is installed
in the vacuum cleaner chamber and that inlet filter and the
outlet filter is installed in the appliance.
11
Switch on the vacuum cleaner by pressing the “on/off”
button (2) .
12
The vacuum cleaner is equipped with electronic power
regulator allowing a stepless regulation of vacuum cleaner
power. The power regulation is performed with a slider.
Moving the slider according to its mark (max or min) will
increase or reduce the suction power.
Filter disassembly
Before changing the filters make sure that the vacuum cleaner
is switched off and unplugged from the mains supply.
INLET FILTER
1 Release the catch of front cover (8) and open it.
2 Remove the inlet filter (15) out of the housing.
3
Replace it with a new one, paying attention that the outer
edge of the filter is placed inside the safety rib.
4 Close the front cover of the vacuum cleaner.
ATTENTION! The damaged inlet filter should be replaced
with a new, genuine manufactured product only.
ATTENTION! It is advised to replace the inlet filter
every 4 replacements of the SAFBAG dust bag, or
even more often, if necessary.
A
C