67
VC3100-001_v01
5
Carefully insert a new / rinsed filter to previously occupied
space.
6
Put the filter cover so that two tips located at the right
side of the cover should hit the holes in the body of the
vacuum cleaner, press the filter cover so the hook snapped
in the body. Characteristic “click” sound informs, that the filter
cover has been properly installed.
Do not use the vacuum cleaner with no inlet
and outlet filters mounted in the device.
Damaged inlet and outlet filters must be always
replaced with new, factory original filters.
THE CONE OF “CYCLONE” DUST CONTAINER
It is necessary to clean periodically the “CYCLONE” dust
container cone.
1
Disassembly “CYCLONE” dust container according to
point
(C)
.
2
Press the button located on “CYCLONE” dust container
and open the bottom of the container. If “CYCLONE dust
container is full, empty it according to the point
(C)
.
3
Turn the cone left, so the two tips located on the flange of
the cone were put out from the slots of the container. Put out
the cone.
4
If the “CYCLONE” dust container cone
(17)
is dirty, you
can rinse it with running water. Do not forget to dry above
mentioned cone before re-installation.
5
Insert the rinsed cone of “CYCLONE” dust container into
the container slot so the tip located on the flange of the cone
was in the slot of container’s body. Turn right the cone so that
the two tips located on the flange of the cone were blocked in
the slots of the container.
6
Snap the bottom of “CYCLONE” dust container. Please
pay attention to the proper positioning of seal found on the
bottom of the container.
7
Insert “CYCLONE” dust container to vacuum cleaner
chamber. The characteristic “click” indicates that the
container has been correctly mounted.
End of operation, cleaning and
maintenance
1
Switch off vacuum cleaner pressing On/Off switch
(4)
.
2
Put the connection cable plug out the wall outlet.
3
Wind the cable by pressing retractor button
(6)
.
Performing this action, hold the power cable to avoid any
tangles and shocking the vacuum cleaner body with the
plug.
4
Disconnect telescopic suction tube and a sucker or
a brush sweeper.
5
Disconnect telescopic suction tube and a hose.
6
Press the two side buttons located at the hose end, then
remove the hose end from vacuum cleaner inlet hole.
F
G
it or rinse with running water. Do not forget to dry above
mentioned filter before re-installation.
The main function of the foam inlet filter
(15)
is to protect
HEPA inlet filter
(14)
against excessive dirt.
For safety reasons it is unacceptable to install
the moist or damaged foam inlet filter (15).
Clean the pleats of HEPA inlet filter
●
(14)
, in case of filter
damage it should be absolutely replaced with a new
filter. If HEPA inlet filter
(14)
is dirty, you can replaced
it with a new filter, you can clean it or rinse with running
water. Do not forget to dry above mentioned filter before
re-installation.
For safety reasons it is unacceptable to install
the moist or damaged inlet filter HEPA (14).
Insert a new/rinsed HEPA inlet foam filter
●
(15)
into
previously occupied space.
3
Insert a new/rinsed HEPA inlet filter
(14)
to the dust
container into previously occupied space.
4
Insert “CYCLONE” dust container with mounted HEPA
inlet filter
(14)
to vacuum cleaner chamber. The characteristic
“click” indicates that container has been correctly mounted.
It is recommended to replace HEPA inlet filter
(14) with a new one every 6 months of use.
Do not vacuum without HEPA inlet filter (14)
installed in “CYCLONE” dust container. Lack
of HEPA inlet filter (14) shall prevent insertion
of “CYCLONE” dust container to the vacuum
cleaner.
“MICROFILTER” OUTLET FILTER AND OUTLET
FOAM FILTER
1
In order to replace “Microfilter” outlet filter
(12)
press the
hook located in the filter cover and pull out the filter cover
from vacuum cleaner.
2
Pull out the “Microfilter” outlet filter
(12)
.
If the “Microfilter” outlet filter
(12)
is dirty, you can replace
it with a new filter, you can clean it or rinse with running
water. Do not forget to dry above mentioned filter before
re-installation.
For safety reasons it is unacceptable to install
the moist or defective “Microfilter” outlet
filter (12).
3
Carefully insert a new / rinsed filter to previously occupied
space.
4
Pull out the foam outlet filter from filter cover
(1)
.
If the outlet foam filter
(13)
is dirty, you can replace it with
a new filter, you can clean it or rinse with running water. Do
not forget to dry above mentioned filter before re-installation.
For safety reasons it is unacceptable to install
the moist or damaged outlet foam filter (13).
E
Содержание Eco Power VC3100
