Zelmer DOT VC1002, Руководство пользователя

Страница: 35 / 38

39
VC1002-002_v01
Appliance elements
A
1 Cord rewind button
2 Suction power regulation lider
3 ON/OFF button
4 Combination brush fastening
5 Handle
6 Plug and cord
7 Outlet filter cover
8 Bag repletion indicato
9 Front cover handle
10 Suction hose
11 Inlet filter (installed in the vacuum cleaner)
12 “Microfilter” outlet filter (installed in the vacuum cleaner)
13 Telescopic suction tube with a fastening hook
14 Reusable bag (1 item)
15 SAFBAG dust bag (1 item)
16 Holder of the bag
17 Small brush
18 Crevice nozzle
19 Small nozzle
20 Switchable combination brush
21 Parquet brush “BNB” (additional equipment – may be
bought in retail centers)
Preparing the vacuum cleaner
for operation
1 Press the side button on the end of the suction hose.
2 Place the end of the suction hose in the vacuum cleaner.
You should hear a distinctive click, if you do it right.
3
Attach the other end of the hose (the handle) to the
suction tube.
4 Adjust the length of the telescopic suction tube by sliding
the slider according to the arrow and pull out/ pull the tube
together.
5
Assemble the appropriate nozzle or brush to the other
end of the suction tube.
6 To clean hard surfaces – wooden floors, plastic floors,
ceramic tiles etc. pull out the brush by pressing the switch on
the combination brush according to the figure .
7
Pull the plug and cord (6) out of the vacuum cleaner.
While pulling out the cord, pay attention to the
yellow stripe which signals the end of the cord.
Further attempts (pulling on cord) may result in
damaging the cord.
8
Plug in the appliance.
Before operation make sure that the bag is installed in the
vacuum cleaner chamber and that inlet filter and the outlet
filter is installed in the appliance.
B
9 Switch on the vacuum cleaner by pressing the “on/off”
button (3) .
10 The vacuum cleaner is equipped with an electronic
suction power controller. The power adjustment is done by
means of a slider. By shirting the slider in a given direction,
you decrease or increase suction.
Filter disassembly
Before changing the filters make sure that the vacuum
cleaner is switched off and unplugged from the mains
supply.
INLET FILTER
1 Open the front cover handle (9) .
2
Pull the bag out of the chamber (see p. E).
3 Remove the inlet filter (11) out of the housing.
4 If the inlet filter (11) is dirty, it may be rinsed with running
water. Remember to dry the filter, before its reinstallation.
Due to safety reasons, it is vital never to install
a damp inlet filter (11).
5 Install a new/the rinsed inlet filter (11) , making sure that
the whole filter is in the socket.
6
Insert a bag into the vacuum cleaner chamber (see
p. E).
7 Close the front cover of the vacuum cleaner.
The damaged inlet filter should be replaced with
a new, genuine manufactured product only.
OUTLET FILTER „MICROFILTER”
1
Press the lock and open the cap of the outlet filter, then
pull the cap out of the cleaner.
2 Take the used outlet filter out (12) .
If the outlet filter
●
(12) is dirty wash it in running water.
Remember to dry the filter before putting it into the
cleaner.
3 Put new/washed filter into the cleaner.
Due to safety precautions never put wet outlet
filter into the cleaner.
4 Put the cap so as to two ledges in the lower part of the
cap match the holes in the cleaner body, close the cap by
pressing it until you hear a characteristic “click”.
Damaged outlet filter should be always replaced
with a new original one.
C
D