Zelmer CK1400, Руководство пользователя

Страница: 36 / 38

38
CK1400-001_v01
Technical data
The technical parameters are given on the rating plate of the
product.
1.7 litre capacity.
The kettle is built in insulation class I and is equipped with
a power cord provided with a grounding wire and a grounding
plug.
The kettle meets the requirements of valid standards.
The appliance is compliant with the requirements of the
following directives:
Low Voltage Directive (LVD) – 2006/95/EC.
–
Electromagnetic Compatibility (EMC) – 2004/108/EC.
–
The product is affixed with the CE mark on the rating plate.
Kettle elements (Fig. A)
1 Spout
2 Plastic spout protection – steam protect
3 Kettle body
4 Water level indicator
5 360° swivel base
6 Lid release button
7 On/off switch (0-I)
8 Handle
9 Anti-deposit filter
10 Cord storage
11 Termo-wskaźnik
Plastic spout protection – steam protect (2)
prevents the steam from being released when
water is boiled. The protection also reduces
energy losses, maintaining the heat inside the
kettle for a longer time.
Preparing the kettle for operation
Before first use, wash the kettle inside (for
washing instructions see the “Cleaning and
maintenance” section), fill it with water up to
the “max” level, boil water four times (each
time use fresh water) and wash the kettle inside
again.
Operating the kettle (Fig. B)
1 Press the button (6) and open the lid.
2 Place the filter (9) in the kettle (if it is not in place).
3
Fill the kettle with the desired amount of water (the level
is visible on the indicator (4) ).
Do not boil the water if it is below the minimum
level or beyond the maximum level on the
indicator (4).
4 Close the lid.
5 Place the kettle on the base (5) .
6
Plug the kettle to a socket provided with an earth pin.
7 Turn the kettle on by pressing the switch (7) – the water
level indicator will light up (4) .
When water is boiled, the thermo-indicator will
turn from brown to red. The red colour informs
that the appliance is hot.
8 After the water is boiled, the kettle will switch off
automatically, the lever switch will return to its starting
position and the power indicator will go off.
If you plan to use the kettle again soon, it is not necessary to
remove the plug from the mains.
Make sure that the maximum kettle capacity
is not exceeded when the kettle is filled with
water.
In the event that an empty kettle is switched
on, it will be switched off automatically by
a thermal device.
To switch on the kettle after it has cooled down
(about 15 min), remove it from the base, fill with
water, replace on the base and switch on by
pressing the switch (7). The cooling down of
the kettle can be accelerated by pouring cold
water into the kettle.
Cleaning and maintenance (Fig. C)
Always allow the kettle to cool down completely
before cleaning!
1 Unplug the kettle from the mains.
2 Remove the filter (9) and rinse it under running water.
3 Clean the outside surfaces with a soft damp cloth and
washing-up liquid.
In order to remove the build-up of hard water film from the
outside and inside walls of the kettle, wipe them with a damp
cloth and vinegar.
4
Rinse the kettle with fresh water.
Various black-coloured, rusty, milky, etc.
deposits may form inside the kettle and float on
the water. This is caused by minerals occurring
naturally in water (calcium, magnesium, iron,
etc.). Such discoloration is not caused by faulty
operation of the appliance and does not affect
its use. In case of substantial accumulation of
mineral deposits, proceed as described in the
“Descaling” section.