Zeiss LSM 880 Скачать руководство пользователя | Manualshive

Страница: 45 / 52

background image

CHAPTER 2 - SETUP REQUIREMENTS

LSM 880

Power Requirements

ZEISS

11/2014 V_05

000000-2071-466

43

2

Power Requirements

The LSM 880 system comes with a mains power supply cord and plug, either CEE red

(3/N/PE 400/230V/16A), or NEMA L 14-30P (2/N/Ground 120/240V/30A), and with the matching
mains socket outlet.

The mains socket outlet must be equipped with a fuse having minimum tripping characteristic C
according to IEC/EN 60898.

Line voltage

3/N/PE 400/230 V AC (±10 %)

2/N/Ground 240/120 V AC (±10 %)

Line frequency

50...60 Hz

50...60 Hz

LSM incl. VIS laser:

Max. current
Power

3 phases at 16 A
Phase 1 = 600 VA max.
Phase 2 = 500 VA max.
Phase 3 = 1500 VA max.

2 phases at 25 A
Phase 1 = 800 VA max.
Phase 2 = 1600VA max.

Power consumption

2100 VA max.

2100 VA max.

Power consumption
Ti:Sa Laser 1
Ti:Sa Laser 2
OPO

800 VA max.
800 VA max.
600 VA max.

800 VA max.
800 VA max.
600 VA max.

Class of protection

I

I

Type of protection

IP 20

IP 20

Overvoltage category

II

II

Pollution degree

2

2

Heat emission (without

Ti:Sa or OPO laser)

2000 W max.

2000 W max.

EMC test according to DIN EN 61326-1 (05/2010)

1. Noise emission according to CISPR 11 / DIN EN 55011 (04/2011)

2. Noise immunity according to table 2 (industrial sector)

The LSM contains sensitive electronics. A few seconds of faulty power can damage parts of the
electronics. The system is therefore equipped with a surge guard, a device that protects the

electronics of the LSM from strong electrical power fluctuations like overvoltage, lightning or other
external influences.

The surge guard is located within the electrical connection box. It works once to protect the
system, then it has to be exchanged. Within warranty, service contracts or any other service visit

ZEISS service will check the functionality of the surge guard and provide a new device if necessary.

Nevertheless, in the rare case of a voltage surge on the power supply line (e.g. from indirect
lightning stroke), a momentary interruption of the acquisition system's functionality is possible. This

is no defect. Acquisition can be continued after starting the ZEN software again. Sample position is
maintained and no damage occurs to the system. A possible protective means to minimize the

probability of a temporary disruption is a transient voltage protector in your facility's power system.

The Ti:Sa laser(s) and OPO need to have a separate electrical connection according to the

instructions of the manufacturer.

When operating the main switch of the LSM 880 NLO the Ti:Sa lasers are not switched on or off.

«
...
43
44
45
46
47
...
»

Содержание LSM 880





















































Отзывы:

Нет отзывов

Похожие инструкции для LSM 880

Бренд: Olympus Страницы: 5

Бренд: Labomed Страницы: 31

Бренд: Motic Страницы: 46

Бренд: THORLABS Страницы: 33

Бренд: EMS Страницы: 6

CxL Polarizing Kit

Бренд: Labomed Страницы: 4

Бренд: Omax Страницы: 12

Бренд: Olympus Страницы: 5

Бренд: FEI Страницы: 8

Бренд: National Страницы: 12

Бренд: Levenhuk Страницы: 16

Бренд: Omax Страницы: 6

EDUBLUE ED.1302-P

Бренд: TQC Страницы: 24

Бренд: PerkinElmer Страницы: 132

RamanMicro 300 Series

Бренд: PerkinElmer Страницы: 102

Бренд: MicroLinks Tech Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды