background image

 
 
 
 
 
Microscope Illuminating System 

Start-Up 

HBO 100 

Focusing and Centering 

Carl Zeiss 

 

 
B 46-0063 e  03/06 

 

15 

3.4  Focusing and Centering the 

HBO 100 Microscope 
Illuminator, self-adjusting 
(423011-9901) 

 

 

 

1 LED key 
2 Collector control knob 

Fig. 9 

Adjustment of HBO 100, self-adjusting  

 

 

 

 

 

Automatic adjustment of the HBO 100 requires 
the collector to be set to mid position. 

• 

Turn the collector control knob (Fig. 9/

2

into mid position. 

After the transformer of the connected 
HBO 100 microscope illuminator was switched 
on, the five minutes warm-up phase begins. 

The LED key (Fig. 9/

1

) lights orange during 

warm-up. 

After the five minutes are over, automatic 
adjustment is started. 

The LED key flashes green during the 
adjustment. 

The adjustment is finished after about 40 
seconds. The LED key lights permanently green 
then. 

If the adjustment failed, the LED key lights red. 

 

• 

In this case, you can start automatic 
adjustment manually by a short pressure 
(approx. one second) of the LED key 
(Fig. 9/

1

). 

 

If the adjustment fails again, check whether 
the lamp has been inserted correctly in the 
base of the HBO 100 (pushed in as far as it will 
go). For this, refer to 

Section 3.1

 

 

Содержание HBO 100





















Отзывы: