background image

 

SET-UP 

Axio Zoom.V16 

Installing and connecting the human interface panel (HIP) 

Carl Zeiss 

 
 

 

05/2012 

435080-9030-701 

23 

3.5

 

Installing and connecting the human interface panel (HIP)  

 

The HIP can be swiveled by about 30° around its longitudinal axis to achieve a convenient 

viewing angle.  Be sure not to exceed the stated swivel range.  Forcible twisting may result in 

damage to the device. 

 

The plug-in power supply  is supplied with four plug adapters  (EURO, US, UK, AUS). Before 

connecting it to the power outlet, choose the appropriate adapter and push it onto the plug-in 

power supply. 

 

Install the HIP (Fig. 8/

3

) to the microscope body (zoom function) or motorized focusing drive (focus 

function) as follows: 

 

Fig. 8 

Installing the HIP control unit  

 

 

Remove the cover (right) from the microscope body or focusing drive (Fig. 8/

1

). 

 

Pull out the connecting cable (Fig. 8/

7

) slightly without applying force and connect it carefully to the 

corresponding HIP connector socket. 

 

Push the cable fully back into the casing without bending it; carefully attach the HIP so that the nose 
(Fig. 8/

2

) on the HIP engages in the groove provided (Fig. 8/

8

). 

 

Screw in the socket head screw (SW 3) (Fig. 8/

6

) as far as it will go using the ball-head screwdriver 

(Fig. 8/

5

). 

 

Push the cover cap onto the HIP (Fig. 8/

4

). 

 

Connect the plug-in power supply to the mains supply. 

 

Содержание Axio Zoom.V16



































































Отзывы: