background image

zebris Medical GmbH 

FDM Technical Data and Operating Instructions 

Page 27/36

 

5  Recommendations for recording data 

To  receive  significant  data  from  FDM  systems  some  principle  guidelines  should  be 
followed. This chapter describes the ideal conditions for recording measurement data. 

5.1  Walking range 

The best conditions for measurements with platforms of the FDM-S type will be reached by 
integration of the system in  a walking range.  The complete walking range must  be plane 
wi

th the surrounding floor. This way the test person won’t know the position of the platform 

and gives a workaround to the tendency that test persons try to walk exactly on the sensor 
area. The width of the stage should be about 1,20m. We recommend a distance of about 
4m from start to FDM-S platform and no less than 3m behind. With such a walking stage it 
is easier to measure normal walking without acceleration or deceleration. 
 
Of course the same set up can be used to measure with the method of first step. The first 
step  method  is  described  as  follow:  The  patient  stands  on  one  side  of  the  platform  in  a 
distance  to  reach  the  platform  by  the  first  step.  For  measurement  the  patient  hits  the 
sensor  area  by  the  first  step  and  moves  on.  This  kind  of  measurement  guaranties 
reproducible  steps  and  results.  Notice:  These  results  differ  more  or  less  from  these  by 
normal walking. 

5.2  Data recording 

Please observe the exercise of the patient strictly. Only steps where the complete ground 
contact  of  the  foot  is  located  on  the  sensor  area  may  be  used  for  evaluation.  If  not  the 
complete foot area was measured by the system (foot did partially not hit the sensor area) 
the step can not be evaluated. 

5.3  Gait velocity 

For  the  measurement  a  normal  (individual)  and  constant  walking  velocity  is  necessary.  
Ideally  an  additionally  measurement,  e.g.  by  photo  sensors,  can  proof  the  velocity  for 
notice.  Naturally  the  patients  adapt  to  the  measurement  situation  within  a  few  minutes. 
After  a  few  trials,  walking  seems  normal.  A  change  in  velocity  of  about  5  %  is  non-
effective. 

5.4  Posture 

A  visual  control  of  the  behaviour  pattern  of  normal  gait  is  recommended.  Trials  with 
atypical  behaviour  pattern  should  be  deleted  from  interpretation.  The  patient  has  to  look 
straight  ahead  and  must  not  be  disturbed  by  paying  attention  to  the  platform  or  monitor. 
Marks on the wall in front of the patient can provide orientation to hit the platform. 

5.5  Acrosclerosis 

Different  measurements  (e.g.  P.R.  Cavanagh, 

The  Foot

  (1994) 

4

,  123-135)  show  an 

increase  of  plantar  pressure  peaks  of  about  30  %  by  acrosclerosis  (e.g.  weals).  The 
interpretation of measurement data has to include the existence of plantar acrosclerosis. 

Содержание 124.3005








































Отзывы: