background image

SP220V2/-E/-F 

2x2 Dual Band 802.11ac Wave 2 Outdoor Access Point 

QSG

 

1

 

Package Contents 

 

 

  

One outdoor access point 

One clamp 

Waterproof cable gland (*Note) 

 

 

 

One ground wire 

One mounting bracket  

+ Four screws 

Waterproof cable gland for 

fiber port (*Note) 

One quick setup guide 

 

 

 

Note:

 SP220V2

 

and

 

SP220V2-E both provides two waterproof cable glands, and SP220V2-F 

provides one waterproof cable gland and one waterproof cable gland for fiber port. 

 

Installation Requirements 

TERMS OF USE: All Ethernet cabling runs must use CAT5e, 24 AWG (or above) Shielded Twisted 

Pair (STP) cabling. In addition, please cut the cable into a proper length, strip the cables on both 

ends, and crimp the wires into RJ45 connectors. It is the professional installer’s responsibility to 

follow local country regulations, including operation within legal frequency channels, output power, 

indoor cabling requirements, and Dynamic Frequency Selection (DFS) requirements. 
 

Mounting the Access Point on the Pole 

Place the mounting bracket to the device using 

four screws (included in the packaging). 

Securely tighten the screws.  

 Attach the clamp to encircle pole and 

the mounting bracket. Securely tighten 

the clamp. 

       

 

 

 

Note:

 Avoid having obstacles or metal plates surround the access point. 

 

Содержание SP220V2 Series













Отзывы: