Zapi COMBI AC0 Скачать руководство пользователя | Manualshive

Страница: 42 / 79

background image

Page - 42/79

AF6ZP0AL - COMBIAC0 & ACE0 - User Manual

3) TILLER

BRAKING

Seconds. It controls the deceleration ramp when the tiller is in braking
position (released). The parameter sets the time needed to decelerate the
traction motor from 100Hz to 0Hz

4) INVERS.

BRAKING

Seconds. It controls the deceleration ramp when the direction switch is
inverted during travel. The parameter sets the time needed to decelerate the
traction motor from 100Hz to 0Hz.

5) DECEL. BRAKING

Seconds. It controls the deceleration ramp when the accelerator has turned
down but not completely released. The parameter sets the time needed to
decelerate the traction motor from 100Hz to 0Hz.

6) PEDAL

BRAKING

Seconds. This parameter determines the deceleration ramp when the travel
request is released and the brake pedal switch is closed.

It sets the time

needed to decelerate the traction motor from 100Hz to 0Hz.

7) SPEED LIMIT BRK

Seconds. It controls the deceleration ramp when a speed reduction has been
activated. The parameter sets the time needed to decelerate the traction
motor from 100Hz to 0Hz.

8) MAX

SPEED

FWD

Percentage.

It determines the maximum speed in forward direction.

9) MAX

SPEED

BWD

Percentage.

It determines the maximum speed in backward direction.

10) HYD SPEED FINE

Percentage. Fine adjustment of the pump motor steering function speed.

11) HYDRO COMPENSATION

Percentage. Adjustment of the compensation function when the pump motor
steering function is active.

12) CUTBACK SPEED 1

Typically from 10% to 100%. It determines the percentage of the max speed
applied when the cutback switch 1, CNA#6 connector, is active. When set to
100% the speed reduction is ineffective.

13) H&S CUTBACK / CB2

Typically from 10% to 100%. It determines the percentage of the max speed
applied when the Hard & Soft function (or cutback 2 function if "H&S
FUNCTION" is ABSENT), CNA#29 connector, is active. When set to 100%
the speed reduction is ineffective.

14) FREQUENCY CREEP

Hz value. This is the minimum speed applied when the forward or reverse
switch is closed, but the accelerator is at its minimum.

15) MAXIMUM CURRENT

Maximum level of the current (percentage of the maximum current of the

«
...
40
41
42
43
44
...
»

Содержание COMBI AC0
















































































Отзывы:

Нет отзывов

Похожие инструкции для COMBI AC0

Бренд: µ-Dimension Страницы: 6

Бренд: CanadianSolar Страницы: 27

Бренд: Champion Global Power Equipment Страницы: 40

AT-IMC100T/SCMM

Бренд: Allied Telesis Страницы: 20

Бренд: xpr Страницы: 12

Бренд: Statpower Страницы: 28

Interface Module XC Modbus

Бренд: Baer Страницы: 10

Бренд: Solplanet Страницы: 55

ICT206012-100AI2

Бренд: ICT Страницы: 2

Бренд: AV Link Страницы: 2

Бренд: Metra Electronics Страницы: 9

Бренд: Qdecoder Страницы: 2

Бренд: LINK-MI Страницы: 6

CSI-5K-S22003-E

Бренд: CanadianSolar Страницы: 29

Delphi Series E24SR

Бренд: Delta Electronics Страницы: 15

Бренд: ICP DAS USA Страницы: 148

Бренд: Z3 Technology Страницы: 76

Бренд: Hall Research Technologies Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды