background image

7

TOO WARM

CCOO2

ZANUSSI

Cool Check Guide

The guide consists of a temperature sensitive strip
sealed in a shelf trim.

When the fridge is operating at the safe temperature
to store food the guide will appear black. If the
temperature rises above this level the guide will
show the words TOO WARM.

Positioning of the Cool Check 

The shelf with the cool check temperature guide
must be placed in the fridge according to the
instructions located on the fridge wall and always
ensure the guide is at the front.

If the Cool Check shows TOO WARM

In certain conditions the temperature guide may
show TOO WARM if:

¥

The fridge is switched off

¥

The door has been recently opened

¥

A quantity of warmer food has been introduced to
the fridge

¥

The fridge temperature is above the
recommended maximum for the safer storage of
food.

The cool check will change to show ÒTOO WARMÒ
very quickly after the door has been opened. It will
however take a number of hours to return to black,
indicating that the temperature is correct.

The appliance should be left overnight and the cool
check examined in the morning. If the cool check
shows TOO WARM, turn the appliance to a colder
setting  leave overnight and examine again the
following morning.

Hints and Tips

¥

The guide is only suitable for use in the model
supplied.

¥

The guide will not operate in the freezer
compartment.

¥

When cleaning the shelf take care not to immerse
in water, and wipe away any spills.

Содержание ZU 7115





















Отзывы: