Zanussi ZHC 900, Руководство по эксплуатации

Страница: 7 / 17

13 GB
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Installation instructions
For easy installation proceed as follows:
• Fixing the wall brackets.
• Fixing the canopy hood.
• Electrical connection and working test.
• Ducting or Recirculation fitting.
• Fitting the telescopic chimney stack.
Fixing the wall brackets.
(Fig. 2a-b)
• Draw a vertical line on the wall, from the centre of the cooking appliance up to the ceiling,
using a marking pen. This is to ensure the correct vertical alignment of the wall fixing
brackets.
• Fixing the wall brackets item 1
Draw a horizontal line on the wall ensuring that the distance from the cooktop is as
follows:
a) when the splasback is to be installed: (fig. 2a) d = 210 mm + H, where H is the height of
the visible part of the splashback; as the splashback can be of different heights, the
correct figure can only be obtained by measuring the actual height of the splashback to
be fitted.
b) without splashback (fig. 2b) d = 860 mm minimum. Mark on the horizontal line the centres
of the two keyholes of the bracket item 1 at a distance Y = 95 mm between the centres of
the holes and the centre of the cooker hood.
• Fixing the wall brackets item 2
a) Place one of the two brackets (item 2 fig. 1 ) 1 or 2 mm from the ceiling or from a horizontal
line drawn between the top of the adjoining wall cabinets, ensuring that the bracket is
level and mark the centres for the keyhole bracket fixing screws.
b) Place the other wall bracket (item 2 fig. 1 ) on the wall at “X” distance. This measurement
should be determined by the height of the upper chimney stack and mark the centres for
the keyhole bracket fixing screws.
• Pilot drill all the hole positions as marked on the wall using an 8 mm drill and fix the wall
brackets 1 - 2 using the rawl plugs and screws supplied.
• Splashback (optional)
When a splashback is to be fitted, the distance between the cooker hood and the cooking
appliances will be determined by the height of the splashback, item
B . The splashback is
to be installed before installing the canopy. If the splashback is to be fixed to the wall
using both the top and bottom fixing holes care must be taken to ensure that the
splashback is fitted at the correct height before fixing it into position. The fitting should
be undertaken by a a competent person with experience in this type of installation.
If the splashback is to be fixed through
only the top fixing holes proceeds as follows:
a) Put the splashback on the worktop as illustrated in fig. 2a ; then holding it against the wall
to ensure that it is correctly positioned mark the holes for the top fixing screws on the
wall.
b) Pilot drill the wall using an 8 mm drill and fix the splashback using the 8 mm rawl plugs
and screws supplied.
c) If the fixing holes in the bottom of the splashback are not to be used to secure the
splashback to the wall the installer should ensure that the bottom edge is tucked down
behind the rear of the worktop.