background image

Anti-tilt protection

Warning!

 Install the anti-tilt protection to

prevent the appliance to fall with incorrect

loads.

Important!

 Make sure you install the anti-tilt

protection at the correct height.

How to install the anti-tilt protection

1.

Set the correct height and area for the ap-
pliance before you attach the anti-tilt pro-
tection.

2.

Make sure that the surface behind the ap-
pliance is smooth.

3.

Install the anti-tilt protection 317 - 322 mm
down from the top surface of the appliance
and 80 - 85 mm from the side of the appli-
ance into the circular hole on a bracket.
Screw it into the solid material or use ap-
plicable reinforcement (wall). You can find
the hole on the left side at the back of the
appliance. See the illustration bellow.

4.

If you changed the dimensions of the cook-
er, you must align the non-tip device cor-
rectly.

80-85

mm

317-

322 mm

Important!

 If the space between the bench

cupboards is larger than the width of the
appliance, you must adjust the side
measurement to center the appliance.

Electrical installation

The manufacturer is not responsible if you
do not follow safety precautions from

chapter "Safety information".

This appliance is supplied with a main plug and
a main cable.

The power cable must not touch the part
of the appliance shown in the illustration.

18

 

www.zanussi.com

Содержание ZCG560N





















Отзывы: