background image

8

A08 Open micro door alarm
If occurs if the door of the motor room is opened. This alarm prevents the motor start.
A09 Open door alarm
It signals, if the micro-door is provided, the opening of the door of the load room.
A10 Oil pressure alarm
This alarm occurs in case the pressure of the motor oil drops; it causes the diesel motor to stop permanently. To re-
start the machine you should  reset the alarm following the procedure described in the above-mentioned paragraph 
and press the  on/off  

 key .

A12/13 Maximum/minimum temperature alarm
It occurs if the actual cell temperature and the one set by the control differ beyond limit the preset on the factory.
A14 Thermal relay alarm
It occurs in  case of anomalous  current absorptions of the electrical motor and causes the machine  to stop. To reset 
the alarm, activate the control unit, disconnect power from the machine, open the electrical panel and restore the 
thermal relay. Power the machine again, and press the on/off  

 key located on the cabin control.

A15 Low battery alarm
If during the  start/stop operation, when the machine stops as the preset temperature (set-point) has been reached,  
a battery voltage lower than 11 Volt for 10 seconds is detected, the re-start on continuous mode is forced.
A16/17 Start failure/ alternator failure
This alarm occurs if, when start attempts are completed (set in factory at 5) the diesel motor is not restarted. The 
causes may be: failed alternator, slackened belts, no  fuel,  blocked motor. If the same alarm occurs during the electri-
cal operation the cause should be the alternator’s inappropriate operation . To restart the machine just reset the alarm 
following the procedure described in the above-mentioned paragraph and press the   on/off  

 key.

A18 Pre-heat water probe failure alarm
It is an only signalling alarm which does not affect the machine operation.

1.10.  Diesel operation de-activation  (Motor blockage)

To activate the blockage to the operation with diesel motor press the 

  key for some seconds until the

 

icon is displayed which indicates the impossibility of operation by diesel motor. Press the  

  key to return to the 

main screen.

Содержание DFZ

















Отзывы: