ZANDER HDK 50/100 Скачать руководство пользователя страница 29

Страница: 29 / 72

Installation

HDK350_EN_01_2005-05-10

All piping must be free from any stress and tension whatever!

Pipes subject to stress may burst due to the load placed on them during
operation. This may cause damage to property and personal injury.

►

Use steel pipes to connect the dryer to the compressed air system.

The following figure shows an installation example.

Compressed air system

Item

Component

Entry, humid air

Compressed air inlet
valve, owner end

Upstream filter

Dryer

Downstream filter

Compressed air outlet
valve, owner end

Outlet, dry air

Example of an installation

►

The connection lines for the upstream filter (3) are to be installed at a slight

incline in the direction of the upstream filter.

►

One shutdown valve each (2, 6) is to be installed at the compressed air inlet

and outlet ends of the dryer.

Installing the electrical connection

Warning against electrical voltage

Only qualified specialist personnel may carry out work on the electrical
system!

Installing the supply cable

The components of the dryer have been connected to the control cabinet at the
factory. You only need to connect the control cabinet to the electrical supply
cable.
The switchbox is provided with a connector where electrical power must be
connected.

Содержание HDK 50/100









































































Результаты поиска

Содержание HDK 50/100

Отзывы:

Похожие инструкции для HDK 50/100

Бренды по названию

Популярные бренды

ZANDER HDK 50/100, Руководство по эксплуатации

Результаты поиска

Содержание HDK 50/100

Отзывы:

Похожие инструкции для HDK 50/100

Бренды по названию

Популярные бренды