manualshive.com logo in svg

Z3 Technology Q603-RPS, Руководство по оборудованию

Поделиться
Скачать
Z3 Technology Q603-RPS Скачать руководство пользователя страница 8

 
 

 CONFIDENTIAL                            

 

DOC-USR-0259-02

 

 
 

8

 

______________________________________________________________________________________

 

Z3 Technology, LLC 

♦ 

100 N 8

th

 ST, STE 250 

♦

 Lincoln, NE 68508-1369 USA 

♦

 +1.402.323.0702

 

 

 

 

 

KEL makes two versions of ribbon cables that physically fit when connecting the encoder to the camera. One 
cable is “straight thru”, with pin 1 connected to pin 1, and another is a “cross” type, with pin 1 connected 
to pin N (N=30 in this case).

 

 

Z3 Technology provides the correct cable as part of the Q603-RPS complete starter kit system. The KEL cable 
is also sold separately (ordering part number: CBL-0025-01).  Please 

ONLY USE THE CABLE PROVIDED BY Z3 

TECHNOLOGY

 to connect the Sony FCB-ER8300 to the I/F Front End PCB of the Q603 30-0103.

 

 

The correct cable is the “straight thru”, with pin 1 connecting to pin 1. The figure below shows the straight 
cable. Note how the connectors at the ends of the cable are positioned in opposite orientation so that pin 1 
on one side connects to pin 1 on the other side.

 

 

 

Figure 5 Correct KEL Ribbon Cable Wiring Diagram

 

 

 

The KEL ribbon cable between the Q603-RPS 30-0103 and the FCB-ER8300 block camera is the only 

Shiny flat side

 

Figure 4 Q603-RPS Connected to the

 

FCB-ER8300

 

Sony Camera Block

 

(Sold Separately)

 

KEL Ribbon Cable

 

(Sold Separately)

 

Содержание Q603-RPS




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды