manualshive.com logo in svg

Z3 Technology Q603-RPS, Руководство по оборудованию

Поделиться
Скачать
Z3 Technology Q603-RPS Скачать руководство пользователя страница 13

 
 

 CONFIDENTIAL                            

 

DOC-USR-0259-02

 

 
 

13

 

______________________________________________________________________________________

 

Z3 Technology, LLC 

♦ 

100 N 8

th

 ST, STE 250 

♦

 Lincoln, NE 68508-1369 USA 

♦

 +1.402.323.0702

 

 

 

2.4

 

Connection to a Generic HDMI Camera

 

A Micro-HDMI port is also available on the Interface Front End PCB of the Q603-RPS 30-0103. See 

Figure 2 

Top side of 30-0103

 above.

 

 

Connector J4 allows for an external HDMI source to be connected to the encoder.

 

This is a standard Micro-HDMI (Type D) connector.

 

 

The pin assignments are standard per HDMI specification and shown in the table below.

 

 

 

Pin  Signal 

Pin  Signal 

1 

Hot Plug Detect 

11  Data0- 

2 

Utility 

12  Clock+ 

3 

Data2+ 

13  Gnd 

4 

Gnd 

14  Clock- 

5 

Data2- 

15  CEC 

6 

Data1+ 

16  GND 

7 

Gnd 

17  DDC_CLK 

8 

Data1- 

18  DDC_DAT 

9 

Data0+ 

19  +5V 

10 

Gnd 

 

 

 

Table 3 PCB J4 Pin Out

 

 

2.5

 

Connect to a HDMI Monitor

 

 

A Micro-HDMI port is also available on the Interface Front End PCB of the Q603-RPS 30-0103. See 

Figure 2 

Top side of 30-0103

 above. 

 

 

Connector J10 allows to connect a HDMI Monitor for pass-through of the camera source.

 

 

This is a standard Micro-HDMI (Type D) connector.

 

 

The pin assignments are standard per HDMI specification and shown in the table below.

 

 

 

Pin  Signal 

Pin  Signal 

1 

Hot Plug Detect 

11  Data0- 

2 

Utility 

12  Clock+ 

3 

Data2+ 

13  Gnd 

4 

Gnd 

14  Clock- 

5 

Data2- 

15  CEC 

6 

Data1+ 

16  GND 

7 

Gnd 

17  DDC_CLK 

Содержание Q603-RPS




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды