Z3 Technology Q603-RPS Скачать руководство пользователя страница 17

Страница: 17 / 19

CONFIDENTIAL

DOC-USR-0259-02

______________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

4.0

30-0146

The 30-0146 is the lightweight board that comes with the Q603-15. The following are its pin outs:

The following table is for pin connector J1:

Note

: The ethernet cable used with these pin connectors is part number CBL-0048-01. This cable can be

purchased separately from Z3 Technology.

Table 7 J1 Q603-15 pin out connectors

Figure 9: Q603-15 PCB Layout

Connector

Type

Function

VDAC_CVBS

/dev/ttyHS1 (UART13) 3.3V LVTTL

UART1

/dev/ttyHS4 (UART0) 1.8V LVTLL and /dev/ttyHS1 (UART15)
3.3V LVTTL

2.5mm stereo jack

Serial port interface, RS232 level. Tip=RX, Ring=TX, Sleeve=GND

Power

Power Supply

USB-C

USB-C Connector

General Purpose
Output

GPIO0. Open Drain output

Table 8: J2, J3, J4, J5, J6, J7 Q603-15 pin out connectors

Note

: The power cable used with pin connector J5 is part number CBL-0047-01. This cable can be

purchased separately from Z3 Technology.

Pin

Signal

GND

RX minus (corresponds to RJ45 pin 6)

RX plus (corresponds to RJ45 pin 3)

TX minus (corresponds to RJ45 pin 2)

TX plus (corresponds to RJ45 pin 1)

GND

Содержание Q603-RPS




















Результаты поиска

Содержание Q603-RPS

Отзывы:

Бренды по названию

Популярные бренды

Z3 Technology Q603-RPS, Руководство по оборудованию

Результаты поиска

Содержание Q603-RPS

Отзывы:

Бренды по названию

Популярные бренды