Z Corporation Spectrum Z 510 Скачать руководство пользователя

Страница: 60 / 76

Spectrum Z™510 3D Printer Hardware Manual

Service Menu and Other Maintenance

www.3dpuser.com

10/2/07

9. Close the printer top cover and press

Cancel

to close the

Bleed Air

dialog in ZPrint.

8.10 Service Print Heads

Service Print Heads

will initiate a standard service on the print heads.

8.11 Prime Wash Line

Prime Wash Line

will remove any air from the wash fluid pumping system. This should be performed upon

initial machine setup and any time the wash fluid is allowed to run dry.

8.12 Stripe Test

Authorized Z CORPORATION service personnel use

Stripe Test

to aid in troubleshooting.

8.13 Cleaning the Spreader Roller / Toggle Roller

1. Open the top cover of the printer.

2. Remove all powder from the build side.

3. Close the printer top cover and place the printer Offline.

4. Lower the build piston all the way down.

5. Manually move the gantry over the build area.

Содержание Spectrum Z 510









































































Результаты поиска

Содержание Spectrum Z 510

Отзывы:

Похожие инструкции для Spectrum Z 510

Бренды по названию

Популярные бренды

Z Corporation Spectrum Z 510, Руководство по оборудованию

Результаты поиска

Содержание Spectrum Z 510

Отзывы:

Похожие инструкции для Spectrum Z 510

Бренды по названию

Популярные бренды