Z Corporation Spectrum Z 510 Скачать руководство пользователя страница 23

Страница: 23 / 76

Spectrum Z™510 3D Printer Hardware Manual

Routine Operations

www.3dpuser.com

10/2/07

5 Routine Operations

The routine maintenance tasks described in this chapter should be performed before every build.

5.1 Preparing the Build Area

IMPORTANT

Use only powder supplied by Z Corporation. Use of any other material may impact the
performance and/or safety of your 3D Printer System and will void warranty of equip-
ment.

1. Preheat printer, if needed. Preheating the printer will reduce the print time if the printer has not reached

the required temperature. To preheat the printer, select the

Preheat Printer

option under the

Service

menu.

2. Lower feed piston by pressing down on the

Feed

DOWN button until the feed piston automatically

drops.

3. Take printer offline by pressing 'Offline' on the control panel.

4. Lift the top cover of the printer.

5. Raise build piston by pressing

Build

UP. Once build piston has stopped, press

Build

UP once. You will

see 'Hold for Unload' on the control panel.

Содержание Spectrum Z 510









































































Результаты поиска

Содержание Spectrum Z 510

Отзывы:

Похожие инструкции для Spectrum Z 510

Бренды по названию

Популярные бренды

Z Corporation Spectrum Z 510, Руководство по оборудованию

Результаты поиска

Содержание Spectrum Z 510

Отзывы:

Похожие инструкции для Spectrum Z 510

Бренды по названию

Популярные бренды