background image

14 

54ZB, 62ZB 

 

Z

-

Beast

 Finish Mower 

Rev:  AUG2014 

Z

-

BEAST 

Operating Instructions 

Changing Cut Height 

Your mower is equipped with an easily  adjustable floating deck, which can be  
adjusted for cut heights of 1½ inches to 5 inches in ½-inch increments.  The deck height 
adjuster is located on the right side of the mower. 
 

How to Change the Cut Height 

 
1. Disengage 

blades. 

 

2.  Extend the deck height handle by pulling it up. 

 

3.  Pull the deck height handle to toward the seat and pivot back or forward to shift the 

deck up or down to the desired height. 

 

4.  Push the deck height handle away from the seat to lock it in the desired position. 

 

5.  After deck height is changed the lever should be pushed back down to its  

original position. 

 
Note: After mowing, remember to raise the deck to its highest position to avoid 
scraping or any other kind of damage to the blades or deck. 

IMPORTANT! The mower belts are adjusted to ensure the blades stop turning within seven (7) seconds of 

releasing the blade control lever. If you are making any belt adjustments whatsoever, for your safety and the 

safety of others around you, you must ensure the belts are re-adjusted to achieve this design specification. 

Mowing 

 

 

 

Thoroughly inspect the area where you plan to 
use the mower. Look for items such as stones, 
sticks , wire, and other foreign objects. If struck 
by the mower, these and other objects may 
become projectiles that could lead to serious 

This mower is equipped with a Soft Start feature. The Soft Start feature 

gradually engages the blades to increase belt, clutch, and engine life. 

NEVER “slam” the blade on/off handle from off to on without pausing an 

adequate time in the Soft Start range. Doing so will cause excess wear 

to the belt, clutch and engine. 

WARNING 

Do not operate the mower with 
defective guards, shields, or 
without the safety devices securely 
in place. 

1.  When the mower is in position on the area to be mowed, move the 

throttle to its full speed. 

 

2.  SLOWLY push the blade control lever forward into the soft start 

range. 

 

3.  When the blades have reached full speed push the blade control lever 

fully into the on position. 

 

4.  Begin mowing as described on the previous page, always using safe/

comfortable speeds. 

 

5.  To stop the blades, pull the blade control lever back to the OFF position. 

WARNING 

Содержание 54ZB




































Отзывы: