YSI ProDIGITAL Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 78

background image

17

Operation

Figure 20

Sampling

Sampling

→

Sampling

Auto sampling mode continuously updates measurements on the display
(

Figure 20

).

When in Manual mode, the instrument will take measurements for the du-
ration of the user-defined Sample Period (in seconds) then “lock” or hold
the readings on the display. The default sample period is 50 seconds, and
can be adjusted from 15 to 60 seconds. Manual mode helps conserve
battery power.

Once the measurements are locked, push the

ENTER

key to log the held

data, or the

Esc

key and then the

ENTER

key to take a new measurement.

NOTE:

When both Continuous Logging Mode and Manual

Sampling mode are enabled, the handheld will power the
sensors on and take measurements for 15 seconds before
logging a data set.

Auto-Shutoff

→

Auto-Shutoff

To conserve battery power, auto-shutoff powers off the instrument after
a user-defined time period (in minutes). The auto-shutoff time can be
adjusted from 1 to 255 minutes. Set to 0 (zero) to disable Auto-Shutoff.

Backlight

→

Backlight

In Automatic mode, the instrument display will dim 60 seconds after the
last key was pushed. Once any key is pushed, the instrument display will
return to the user-defined brightness setting and the keypad backlight
will turn on. The screen will dim and the keypad backlight will turn off
after another 60 seconds of inactivity.

In manual mode, the instrument display remains at the user-defined
brightness and the keypad backlight is turned on and off by the Backlight
key. Setting the backlight to manual mode is recommended for bright
conditions.

«
...
15
16
17
18
19
...
»

Содержание ProDIGITAL















































































Отзывы:

Нет отзывов

Похожие инструкции для ProDIGITAL

Бренд: DayTronic Страницы: 54

Бренд: Bacharach Страницы: 2

Бренд: Bachmann Страницы: 33

Бренд: NanoEnTek Страницы: 4

Бренд: CA.MI Страницы: 68

Бренд: H. HERMANN EHLERS Страницы: 40

GRAND RHAPSODY PIANO

Бренд: Waves Страницы: 19

Бренд: az-instrument Страницы: 12

Бренд: Bartington Страницы: 32

Бренд: Alfano Страницы: 47

ENSEMBLE GRANDE MARK 5

Бренд: Kurzweil Страницы: 32

Бренд: MEWOI Страницы: 21

Digital Piano CN41

Бренд: Kawai Страницы: 80

Бренд: LCR Страницы: 32

Бренд: Easy-Laser Страницы: 86

Бренд: Jacob Jensen Страницы: 24

Бренд: Ralcam Страницы: 14

Бренд: Apera Instruments Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды