background image

31

youngmangroup.com 

 

Prior to operating the platform, the following 
items must be checked:

Machine Number    

 

Check

OK? 

 Hydraulic oil leaks by visual 

inspection of  the floor around 

the base unit and by feeling 

underneath the base unit tray

 Loose electrical fittings and 

sensors by visual inspection

 Chafed hydraulic hose or 

electrical cables by visual 

inspection

 Condition of  castors, tyres and 

brakes by visual inspection

 Structure – guardrails, platform, 

scissors and chassis (eg 

damage, cracks, corrosion, 

abrasions, welds, connections)

 Visual inspection of  the 

castellated scissor nuts and the 

split pin retainers

 Obscured, dirty or damaged 

instruction labelling and plates

 Emergency stop function 

activated on the handset

 Emergency stop function 

activated on the base unit.

 Emergency lowering of  platform 

(see page 19)

 Raise and lower functions 

including descent delay (the 

raise and lower functions can be 

tested by removing the handset 

controller from its holder on the 

work platform and using the 

controls whilst at ground level)

 Without the swivel castor brakes 

applied and on a level surface 

raise the platform until, the 

auto fixed castor brakes are 

engaged. Try to push the 

machine from the left and right 

hand side of  the gate end of  the 

machine to ensure the brakes 

are functioning.

 Switch on power and:

   ensure that the tilt sensor alarm 

sounds to confirm operation

 check that the battery is fully 

charged

 

WarnIng 

Should any defects be identified in any of the 

above areas, these should be reported to your 

employer. It may be necessary to seek further 

assistance from the supplier of the machine, this 

may be the hire company or the manufacturer. 

You should only rectify any defects if you are 

authorised and competent to do so. 

Do not use this machine unless each of the 

items above is checked and stated as OK

7.5 DaIly checks - oPerator checklIst

Содержание BOSS X Series









































Отзывы: