1
IIn
nttrro
od
du
uc
cttiio
on
n
The LS700P is a premium quality integrated powered subwoofer and amplifier. Created
as an easy-to-setup addition to your PA, the LS700P will extend the bass of a typical
sound system with a minimum of complication, and hence is intended primarily to
operate with speaker level signals.
C
Co
on
nffiig
gu
urra
attiio
on
n
The LS700P may be used in several different configurations, the minimum standard
system is one LS700P used with a pair of full range speakers. The LS700P accepts the
signal from separate Left and Right sources simultaneously. It then combines them into
one signal (to drive the internal speakers). When used in a setup where only one signal is
provided to a speaker, such as a mono system or stereo with more than one LS700P, use
either the Left or Right input.
USER NOTE:
This Subwoofer may be driven from Speaker Level
or Line Level signals. If an élite processor is used,
this Subwoofer should be plugged into the SUB
output of the processor. The
High–Frequency
Cutoff should be set to 150-Hz and the Input Level
should be set to LINE. For Line
Level operation a balanced (
Tip
Ring Sleeve) cable should be
used. If the system is being
operated
without a processor,
this Subwoofer can be
connected to the output of the
power amplifier as shown in the
diagrams and the Input Level
should be set to SPEAKER. If
none of the equipment has a U-
ground, the INPUT GROUND
should be set to
GROUNDED.
Otherwise the INPUT GROUND
should be set to the position that
best minimizes the hum.
Refer to the Owner's
Manual for other modes
of operation
+3
-3
+10
+30
+20
dB
LS700P
Yorkville
DESIGNED & MANUFACTURED BY YORKVILLE SOUND • TORONTO, CANADA
INPUT GROUND
INPUT LEVEL
LEFT
(mono)
RIGHT
HIGH
FREQUENCY
CUT OFF
125 Hz
POWER
100 Hz
150 Hz
SUBWOOFER
LEVEL
PARALLEL
THRU
I
N
P
U
T
PARALLEL
THRU
I
N
P
U
T
CAUTION AVIS
UNGROUNDED
GROUNDED
SPEAKER
LINE
ON POWER
ES700P
SUBWOOFER
POWER
AMPLIFIER
FULL–RANGE
SPEAKERS
Left
Right
Left
Right
ONE SUBWOOFER PER SYSTEM
0
ES700P
SUBWOOFER
ES700P
SUBWOOFER
POWER
AMPLIFIER
FULL–RANGE
SPEAKER
FULL–RANGE
SPEAKER
TWO SUBWOOFERS PER SYSTEM
R
L
CAUTION: REPLACE WITH
SAME TYPE FUSE AND RATING
ATTENTION: UTILISER UN FUSIBLE DE
RECHANGE DE MEME TYPE ET CALIBRE
Yorkville
230V
50Hz
1.3A
120V
60Hz
2.5A
LR 21877
T 3,15A GDC
T 5.0A 250V
SLO~BLO
For normal operation connect the
LS700P
LS700P
LS700P
LS700P
LS700P
LS700P
just like an ordinary speaker along with the full range speakers. The
"
INPUT LEVEL
" switch should be set to "
SPEAKER
." If the audio source does not have a "U" ground, eg. a ground pin on
the AC cord, the "
INPUT GROUND
" switch must be set to "
GROUNDED
." The
may be wired before or after
the full range speakers. Use the left and right inputs when using a single
in a stereo system. Use either
the left or right inputs when using separate
's for each side or when used in a mono system. The
does not alter the signal to the full range speakers in any way. The
will not draw any
power from the amplifier driving the full range speakers. Please note that an external cross-over is not necessary.
1
1.. H
Hii F
Frre
eq
qu
ue
en
nc
cy
y C
Cu
utto
offff C
Co
on
nttrro
oll
This control varies the frequency at
which the LS700P rolls off the high
frequencies. This provides part of a
crossover function. This crossover
function also combines with the natural
low frequency roll off inherent of the full
range cabinet (when the LS700P is not
used with an élite processor). This control
should be set to the closest possible
frequency to 20 Hz below the crossover
point that the full range speakers
processor uses as it's crossover point.
If an élite processor is used, set the high
frequency cutoff to maximum (160 Hz)
2
2.. S
Su
ub
bw
wo
oo
offe
err L
Le
ev
ve
ell C
Co
on
nttrro
oll
The subwoofer level control adjusts the
amount of bass added to the sound
system by the LS700P. This adjusts for the
relative sensitivity of the companion full
range speakers and the desired system
frequency response. This control should
be set by listening while operating at a
medium level and then not changed. It
is not possible to set this control properly
at high levels since the limiter is
determining the output level. Setting the
level too high will over load the circuitry
causing a loss of bass dynamics. The
level control should not be set above
