York ZJ078 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 69

background image

524581-YIM-I-0512

6

Johnson Controls Unitary Products

3.

Gas-Fired Central Furnace Standard, ANSI Z21.47 Latest
Edition

4.

Local building codes, and

5.

Local gas utility requirements

In Canada:

1.

Canadian Electrical Code, CSA C22.1

2.

Installation Codes, CSA - B149.1.

3.

Local plumbing and waste water codes, and

4.

Other applicable local codes.

Refer to unit application data found in this document.

After installation, gas fired units must be adjusted to obtain a
temperature rise within the range specified on the unit rating
plate.

If components are to be added to a unit to meet local codes,
they are to be installed at the dealer’s and/or customer’s
expense.

Size of unit for proposed installation should be based on heat
loss/heat gain calculation made according to the methods of Air
Conditioning Contractors of America (ACCA).

This furnace is not to be used for temporary heating of buildings
or structures under construction.

Figure 4: Predator

®

Component Location (ZJ120 Shown)

The

Simplicity

® control board used in this product will

effectively operate the cooling system down to 0°F when
this product is applied in a comfort cooling application
for people. An economizer is typically included in this
type of application. When applying this product for
process cooling applications (computer rooms,
switchgear, etc.), please reference applications bulletin

AE-011-07 or call the applications department for

Unitary Products @ 1-877-UPG-SERV for guidance.

Additional accessories may be needed for stable

operation at temperatures below 30° F.

Roof curbs in eight- and
fourteen-inch heights. Roof
curbs for transitioning from
York Sunline™ footprint to
the ZJ Series footprints
are also available (field
installed accessory)

Base rails w/forklift
slots (three sides)
and lifting holes

Compressor #2
access (high-
efficiency
compressor
w/crankcase
heater)

Dual stage
cooling for
maximum
comfort

Second model
nameplate
inside hinged
access panel

Terminal block for
hi-voltage connection

Simplicity

®

control board

w/screw connector for T-stat
wiring and network connections

Disconnect location
(optional disconnect switch)

Filter drier
(solid core)

Slide-out motor and
blower assembly for
easy adjustment
and service

Belt-drive
blower motor

Power ventor motor

20-gauge alumi-
nized steel tubular
heat exchanger for
long life (stainless
steel option)

Two-stage gas
heating to maintain
warm, comfortable
temperature

Intelligent control
board for safe and
efficient operation

Compressor #1 access
(high-efficiency compressor
w/crankcase heater)

Toolless
door latch

Side entry power
and control wiring
knockouts

VFD Location (optional)

Filter access
(2” or 4” Filter Options)

Micro-Channel Aluminum Tube
Aluminum Fin Condenser

Slide-out drain pan
with 3/4” NPT,
female connection

«
...
4
5
6
7
8
...
»

Содержание ZJ078






































































Отзывы:

Нет отзывов

Похожие инструкции для ZJ078

Бренд: Kahn Страницы: 8

Бренд: RS Страницы: 12

1PAMSH09-SZO-14.5

Бренд: Perfect Aire Страницы: 12

Бренд: Vertiv Страницы: 44

Бренд: Danby Страницы: 12

Arctic NG Wi-Fi Series

Бренд: Cooper & Hunter Страницы: 111

Mini Amazon 3 KMF-80 DVN4

Бренд: Kaysun Страницы: 16

Бренд: ABCOOLAIR Страницы: 24

Бренд: IP Enclosures Страницы: 16

Бренд: Daewoo Страницы: 22

Бренд: J&E Hall Страницы: 36

Бренд: Sinclair Страницы: 48

Бренд: Sabiana Страницы: 40

Бренд: Germ Guardian Страницы: 18

Бренд: Daikin Страницы: 60

Бренд: Haier Страницы: 32

Бренд: Haier Страницы: 48

Бренд: Haier Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды