background image

Ceiling

Walls

Pattern board

Fig. 3.3.7

12

Installation and Maintenance

The outlet through which the pipings are

taken out is available in three directions.

 

Pipes can be taken out in 3 directions(rear, right 

or top).(See fig.3.3.3)
Cut out holes using nippers, etc.
Cut out holes to taken out pipes along the cutoff line 
on the rear cover.
Cut out the top face cover aligning to the piping 
position.
When taking pipe out to right-hand side, cut out a 
hole along the groove at the inside of the side 
panel.
After installing pipes and wires,seal clearances 
around pipes and wires with putty,etc. to shut off 
dust.
Make sure to install the covers at rear and top in 
order to protect the inside of unit from intrusion of 
dust or protect wires from damages by sharp edges. 
When taking them out to the right-hand side, 
remove burrs or sharp edges from the cutout.

Top outlet

Right outlet

Rear outlet

Drain outlet

 (rear right)

Drain outlet

  (rear left)

Drain outlet

    (right)

Drain outlet

     (left)

Fig. 3.3.3

Fig. 3.3.4

Fig. 3.3.5

Slide stoppers (4 places) of the catches, then 

remove the screws(4 or 6 places).

(

1)Remove the air return grille.

3.3.3Indoor unit preparation

Remove the screw and detach the side panel by 

sliding it toward the direction indicated by the 

arrow mark.

(2) Remove side panel.

Fig. 3.3.6 Suspension bolts and nuts

Remove the screw and then fixing bolts.

(

3) Remove the hanging plate.

UNIT

:

mm

Ceiling type installation

(1)Select the suspension bolt locations and the pipe 
hole location.

.Use enclosed paper pattern as a reference, and drill 

the holes for the suspension bolts and pipe.
Note:Decide the locations based on the direct 
measurements.
ii.Once the locations are properly placed, the paper
pattern can be removed.
2)Install the suspension bolts in place.

i

Side panel

           Side panel screw

(1 each on the left and right)(M4)

Hanging plate

Hanging plate

fixing bolts(M8)

Hanging plate

  screw (M5)

3.3.4Install the indoor unit

Screw

Screw

Содержание YFKN18BZNREUH1
























Отзывы: