background image

Installation and Maintenance

9.2 Connecting piping between Indoor 
        and Outdoor Units

Be sure to apply a sealing cap or water-proof tape 
to prevent dust or water from getting into the tubes 
before they are used.
Be sure to apply refrigerant lubricant to the 
matching surfaces of the flare and union before 
connecting them together

. This is effective for 

reducing gas leaks.(Figure 9.4)
For proper connection, align the union tube and 
flare tube straight with each other, then tighten the 
flare nut lightly to obtain a smooth match. (Figure 89.5) 
Tighten the sets crew with torque wrench to prevent 
leak of refrigerant. Carefully test leak before running 
the appliance.

Remove the burrs at the end of the copper tube 
with a tube reamer or file. When reaming, hold the 
tube bend downward and be sure that no copper 
scraps fall into the tube. This process is important 
and should be done carefully to make a good 
flare.(Figure 9.1,9.2)
Remove the flare nut from the unit and be sure to 
mount it on the copper tube.
Make a flare at the end of copper tube with a flare 
tool.(Figure 9.3)

9.4 Taping the Tubes

Note: Do not bind the armoring tape too tightly because 
this will decrease the heat insulation effect. Also be
sure the condensed drain hose splits away from bundle 
and drips clear of the unit and the piping.  

The two refrigerant tubes (and electrical wire if local 
codes permit) should be taped together with white 
armoring tape. The drain hose may also be included 
and taped together as a bundle with the piping. 
Wrap the tape from the bottom of the outdoor  unit 
to the top of the piping where it enters the wall. As 
you wrap the piping, overlap half of each previous 
tape. (See Figure 9.7)
Clamp the piping bundle to the wall, using one 
clamp approx. every 120 cm.

9.5 Finishing the installation

After completion of wrapping and insulation, seal the 

hole on the wall with suitable seal against wind and rain.

To avoid loss of heat and in prevention of the 
ground being wet by condensed water, all 
refrigerant tubes must be insulated with suitable 
insulating materials whose minimum thickness will 
be 6 mm. (See Figure 9.6)

9.3 Heat Insulation of the Refrigerant Tube

9.1 Flaring with Tube Expander 

Note: A good flare have the following characteristics:
Inside surface is glossy and smooth.
Edge is smooth.
Tapered sides are of uniform length.

9.Refrigerant piping

Clamp 

Insulated tubes

Tube

Tapered nuts

Flarer 

 Fig.9.3

Apply refrigerant  lubricant here and there

Union    Flare nut

Insulation 

Tube

Reamer 

Fig.9.1

Before 

After 

Fig.9.2

 Fig.9.5

 Fig.9.4

 Fig.9.6

 Fig.9.7

18

Содержание YFKN18BZNREUH1
























Отзывы: