background image

WIRING DIAGRAM

 CONTRACTOR _________________________      PURCHASER _____________________________________________ 
 ORDER NO. ____________________________      JOB NAME ________________________________________________ 
 JCI CONTRACT NO. _____________________      LOCATION ________________________________________________ 
 JCI ORDER NO. _________________________      ENGINEER _______________________________________________

REFERENCE       DATE ________            APPROVAL      DATE ________ 

CONSTRUCTION       DATE _______

Supersedes: 160.79-PW2 (616) 

Form: 160.79-PW2 (119) 

FIELD CONTROL MODIFICATIONS 

FOR YD CHILLER (STYLE D) 

WITH OPTIVIEW CONTROL CENTER

Issue Date:  

January 31, 2019

JOB DATA:

CHILLER MODEL NO. YD _________________

NO. OF UNITS __________________________

TYPE OF STARTING _____________________

Included by Johnson Controls for Field Installation (by others) are:   

 

 

 

 

 

 

 

 

 

 

 

    YES      NO     Per Unit 

 

Chilled Water Flow Switch

Condenser Water Flow Switch

_______________________________________________________________

_______________________________________________________________

Содержание YD





















Отзывы: