background image

 

 

<1.  GENERAL>

1-11

IM 12T03A01-02E

1.4 

Cautions in Handling Flameproof, 

Explosion-proof Instruments

1.4.1 

Outline of Explosion-proof Instruments

Specifications of “Explosion-proof Instruments” conform to the regulations of relevant public 

organizations.

Model DM8 Vibration Type Liquid Density Meter consists of a density detector and a density 

converter. Model VD6DF density detector, explosion-proof instrument, can be installed in 

hazardous area where explosive gases may be generated.

It should be noted, however, that the method of installation, ambient conditions, and the handling 

of these instruments must conform to the regulations of relevant public organizations. The 

applicable explosion-proof regulations and the cautions marked on the analyzer shall be strictly 

observed when using Model VD6DF in a hazardous location.

WARNING

Model VD6D and Model VD6DS Density Detector, which are not “explosion-proof instrument”, 

cannot be installed in hazardous location.

Model VD6DF density detector has either TIIS or FM flameproof type of explosion-proof 

specifications. The TIIS type has passed tests conducted by a public authority in accordance with 

the Labor Safety and Health Law (Japan) which regulates domestic explosion-proof electrical 

equipment. The FM type has been certified to have an explosion-proof construction meeting the 

requirements of NEC (National Electrical Code) by Factory Mutual Research Corporation, U.S.A. 

(FM), a testing organization. It also conforms to requirements of OSHA (Occupational Safety and 

Health Act, U.S.A.).

Items 1.4.2 to 1.4.6 cover general cautions in using the Model VD6DF density detector. For 

further details, see the following publications:

•  For TIIS flameproof requirements
  ‘RECOMMENDED PRACTICE’ for Electrical Equipments for Use in Explosive Gas 

Atmosphere published by The Research Institute of Industrial Safety, Ministry of Labor.

•  For FM Flameproof requirements
  National Electrical Code, Chapter 5, Special Occupancies.

1.4.2 

Labeling the Explosion-proof Specifications

TIIS Flameproof type of explosion-protected construction

The Model VD6DF density detector is labeled data plate on which type of the explosion-

protection constructions, approval number, symbols for the type and working ambient 

temperature range.

Table 1.1  TIIS Flameproof Type (Explosion-proof) Construction of Vibration Density Detector

Model and codes

Type Approval No.

Symbol for the type (including 

explosion class and ignition group)

Model VD6DF-N1

Model VD6DF-S3

No. T21726

No. T21727

d2G3

d2G3

FM Explosion-proof Specifications

The Model VD6DF density detectors complying with FM explosion-proof specifications is labeled 

data plate which is marked with an approval mark, classification of hazardous location, working 

ambient temperature range, and handling cautions.

5th Edition : Dec. 11, 2015-00

Содержание vigilantplant DM8
































































Отзывы: