background image

Yokogawa Electric Corporation - TC10-L - ENGINEERING MANUAL - PAG. 13

6.3  ACCESS LEVELS AND SPECIFIC 

PARAMETERS

The instrument is showing the “standard display”
This instrument is equipped with 3 different access 
levels:Level 1 – Operator Mode.(not protected by password)
Level 2 – Operator modify parameter (protected by a pro-
grammable password [default 20])
Level 3 – Confi guration parameters mode (protected by pro-
grammable password [default 30])

•  The operator area (Level 1) allows: confi rmation 

action,  to see and to reset the  << tim >> parameter 
(time duration of the last shutdown condition detected) 
and to see and to reset the << Min/max >> (minimum 
or maximum measured value during  last shutdown 
condition detected). 

Note: 

when a new shutdown condition is detected, the 
instrument automatically reset << tim>> and << min/
max >> parameters and start to memorize the values 
related with the new shutdown condition only.  At the 
end of the shut down condition, <<tim>> and <<min/
max>> can be read and reset.

•  The Level 2 area encompasses the following 

parameters:

Param.

Description

Dec.

Point

SP

 Set point (shutdown set point)

dP

AL1L

For high or low alarm, it is the low limit of AL1 
threshold

dP

For band alarm, it is low alarm threshold

AL1H

For high or low alarm, it is the high limit of AL1 
threshold

dP

For band alarm, it is high alarm threshold

AL1

Alarm 1 threshold

dP

AL2L

For high or low alarm, it is the low limit of AL2 
threshold

dP

For band alarm, it is low alarm threshold

AL2H

For high or low alarm, it is the high limit of AL2 
threshold

dP

For band alarm, it is high alarm threshold

AL2

Alarm 2 threshold

dP

HyS

Hysteresis of the shutdown control (relay hyster-

esis for control output)

dP

Fil

Digital filter on the measured value

1

bS

PV input bias

6.4  ENTER THE “OPERATOR  MODIFY 

PARAMETER”

The instrument is showing the “standard display”.

1. 

Press the 

 button for more than 3 seconds;

2. 

The upper display will show 

PASS

 while the lower display 

will show 

0

;

3. 

By 

 and 

  buttons set the value assigned to [44] 

PAS2 (Level 2 password).

Notes:  1. 

The factory default password for confi guration 
parameters is equal to 20.

2. 

 All parameter modifi cation are protected by a 
time out.  If no button is pressed for more than 
30 second the instrument comes automatically 
back to the Standard display, the new value of the 
last selected parameter is lost and the parameter 
modifi cation procedure is closed.When you 
desire to remove the time out (e.g. for the fi rst 
confi guration of an instrument) you can use a 
password equal to 1000 plus the programmed 
password  (e.g. 1000 + 20 [default] = 1020).It is 
always possible to manually End the parameter 
confi guration procedure (see below). 

4. 

Push 

  button.

5. 

The instrument will show on the upper display the 
acronym of the fi rst parameter promoted to this level and 
on the lower display its value.

6. 

By 

 and 

  buttons assign to this parameter the 

desired value.

7. 

Press the 

 button in order to memorize the new value 

and go to the next parameter.

8. 

When you want to come back to the “standard display” 
push the 

 button for more than 3 s.

6.5  HOW TO SEE BUT NOT MODIFY THE 

“OPERATOR MODIFY PARAMETERS 
ACCESS PARAMETERS”

Sometime it is necessary to let the possibility to see the 
value assigned to the Operator Modify Parameter but it is 
important that changes are made by authorized personnel 
only.In this cases, proceed as follows:

1. 

Press the 

 button for more than 3 seconds;

2. 

The upper display will show 

PASS

 while the lower display 

will show 

0

;

3. 

By 

 and 

 button set the value 

-181

;

4. 

Push 

 button;

5. 

The upper display will show the acronym of the fi rst 
parameter promoted to the level 2 and lower display will 
show its value;

6. 

Using 

 button it is possible to see the value assigned 

to all parameter present in level 2 but it will not be 
possible to modify it;

7. 

It is possible to come back to the “standard display” by 
pushing the 

 button for more than 3 seconds or by 

pushing no pushbutton for more than 30 seconds.

Содержание TC 10-L





















Отзывы: