YOKOGAWA N-IO Скачать руководство пользователя

Страница: 3 / 52

TI 30A30A10-01EN

Introduction

The N-IO field enclosure is a standardized remote I/O enclosure for outdoor use, which

include N-IO node. There are two types of N-IO field enclosure, one is for CENTUM VP and

the other is for ProSafe-RS.
This document provides guidance that allows users to consider how to accumulate

the power capacity and install devices at a planning stage of deploying the N-IO field

enclosures for CENTUM VP and ProSafe-RS.

Chapter 1 System installation requirements

This chapter describes specifications covering N-IO field enclosure installation and

environmental specifications, inrush current, power consumption, noise prevention, and

grounding necessary for designing a power supply system.

Chapter 2 Transportation, storage and installation

This chapter describes general cautions for transporting and carrying the N-IO field enclosure

which is a precision device, precautions for temperature and humidity changes when unpacking

or storing it temporarily, space necessary for maintenance (servicing area), and how to install

devices.

Chapter 3 Cabling
This chapter describes how to connect power, grounding, signal and communication cables to

the installed devices, and how to connect optical fiber cables.

Chapter 4 Installation specifications
This chapter covers power consumption and power dissipation, in-rush current, circuit protector

and breaker ratings, and parts that need replacement within 10 years. Read this section when

deciding power supply capacity.

Chapter 5 Post-installation inspection and environmental preservation

This chapter describes items that must be checked before applying power and the precautions to

be taken to safeguard the environment after installing the system.

Feb. 26, 2018-00

Содержание N-IO





















































Результаты поиска

Содержание N-IO

Отзывы:

Похожие инструкции для N-IO

Бренды по названию

Популярные бренды

YOKOGAWA N-IO, Руководство по установке

Результаты поиска

Содержание N-IO

Отзывы:

Похожие инструкции для N-IO

Бренды по названию

Популярные бренды