manualshive.com logo in svg

YOKOGAWA FC500G, Руководство пользователя, Страница: 2 / 41

Поделиться
Скачать
YOKOGAWA FC500G Скачать руководство пользователя страница 2

i

IM 12F5A2-01E

 Introduction

This user’s manual describes the specifications, installation, operation, maintenance, and 

troubleshooting for Model FC500G Free Available Chlorine Analyzer. Read this manual 

thoroughly to understand the contents before operating the equipment.

n

  Notes on Hardware

l

  Appearance and Accessories

Check the following when you receive the product:

• Appearance
•  Standard accessories

Contact our sales representative or your local distributor if the product’s coating has come off, it 

has been damaged, or there is shortage of required accessories.

l

  Model and Suffix Codes

The name plate on the product contains the model and suffix codes. Compare them with those in 

the general specification to make sure the product is the correct one. If you have any questions, 

contact our sales representative or your local distributor.

Media No. IM 12F5A2-01E 

5th Edition : July 2018 (YK)

All Rights Reserved Copyright © 2007, Yokogawa Electric Corporation

Содержание FC500G










































Отзывы:

Нет отзывов