YOKOGAWA FC500G Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 41

YOKOGAWA FC500G Скачать руководство пользователя страница 17

<3. INSTALLATION, PIPING, AND WIRING>

3-2

IM 12F5A2-01E

3.1.2 Mounting

Mount the FC500G free available chlorine analyzer (non-reagent type) on a wall surface. For

mounting holes, see section 1.3.

3.2 Piping

3.2.1

Sample Water Piping

Connect a 6 mm OD X 4 mm ID polyethylene tube to the sample water inlet. Set the sample

water pressure at the sample water inlet to 1 to 30 kPa (flow rate: 0.1 to 2.5 l/min).

Note: If a sample water inlet valve is used, set the pressure at the valve inlet to 10 to 150 kPa.

Connect a hose of 12 mm lD to the sample outlet. Make piping so that no drain stagnates in the

hose.

3.2.2

Air Purge Piping

Make the air purge piping only when the FC500G-5 free available chlorine analyzer is used.
The air purge piping connecting port (1/8 NPT female) is located at the electrode assembly.

Exercise care in piping because the electrode assembly must be removed in implementing

inspection or maintenance (see Figure 3.2).

Inspection or

maintenance

Electrode

assembly

Measuring

tank

Detector

Pressure regulator

6 mm OD X 4 mm ID

polyyethylene tube

Air supply

Figure 3.2

Air Purge Piping

«
...
15
16
17
18
19
...
»

Содержание FC500G










































Отзывы:

Нет отзывов