background image

 

 

SAFETY PRECAUTIONS 

 

 

A brief description of signal words that may be used in this manual: 
 
CAUTION:   

Used as a general reminder of good safety practices or to direct attention to unsafe practices. 

 

WARNING:  

Denotes a specific potential hazard. 

 

DANGER:    

Denotes the most serious specific potential hazard. 

 

 

  CAUTION 

Consult your implement and tractor operator’s manual for correct and safe operating practices.  Be aware of towed 
implement width and allow safe clearance. 

 

  CAUTION:  SAFETY SIGNS 

 

Safety  decals  are  placed  on  the  implement  to  alert  the  operator  and  others  to  the  risk  of  personal  injury  or  unsafe 
operation during normal operations and servicing. 
1.  The safety decals must be kept clean and in good condition to ensure that they are legible. 
2.  Safety decals must be replaced if they are missing or illegible. 
3.  When  components  are  replaced  during  repair  or  servicing,  check  that  the  new  components  include  the 

necessary safety signs. 

4.  Replacement safety decals may be obtained from your local dealer. 

 

  WARNING 

 

Read  these  instructions  carefully  to  acquaint  yourself  with  the  Equipment.    Working  with  unfamiliar  equipment  can 
lead to accidents. 
 
Never park the equipment on a steep incline or leave the equipment running unattended. 
 
Never clean, lubricate or adjust a machine that is in motion. 
 
Always check that straps are secure. 
 
Make sure latches are in pinned position when moving equipment. 
 
Do not allow children to operate this equipment. 
 
Do not allow riders on the equipment, trailer and/or pick-up. 
 
Use speed and caution dictated by the terrain being traversed.  Do not operate on any slope steep enough to cause 
tipping or loss of control. 
 
Read and understand the operator’s manual and require all other persons who will operate the equipment to do the 
same. 
 
If operating on public roadways, where legal, be certain all lighting is operating properly and observe all traffic laws. 
 
Beware of increased stopping distances and control effort when operating with implements attached. 
 
Be familiar with all controls and be prepared to stop equipment quickly in an emergency. 
 
 

FAILURE TO HEED MAY RESULT IN PERSONAL INJURY OR DEATH. 

 
 
 
 

 

Содержание CAB CONTROL STRIP FRESHENER 2984-050-R





































Отзывы: