manualshive.com logo in svg

YEO-KAL 615, Руководство пользователя, Страница: 27 / 48

Поделиться
Скачать
YEO-KAL 615 Скачать руководство пользователя страница 27

 

 

27 

already be allocated with 611 sensors so go to page 3. Note: The previously allocated 
sensors can be reallocated to other pages and lines. 

To add a GPS to the display Select page 3 if the 611 is already allocated. Then select the 
line you wish to allocate GPS to. Press ENTER then use arrow keys to select the correct 
parameter (LATITUDE) and press ENTER. Use the same procedure for (LONGITUDE) and 
select the next line for longitude. 

Set Precision (5) 

Press ENTER and select the parameter to be measured and then press ENTER and use 
arrow keys to select the precision of reading eg XXX.XXX 

Press ENTER or ESC to go to next parameter or ESC to the set up menu. 

Connect the Reader Unit to a PC serial port  and call up a previously stored calibration 
constants. Press ENTER and WAITING FOR FILE WILL appear on the LCD display. Use a 
terminal program to send the file to the 615 Reader Unit. 

Note, the terminal program must be set to the following protocol: 

Baud rate: 9600 

Parity: None 

Stop bits: 1 

Flow Control: None 

Date Format (6) 

The date and time is in 24 hour format and defaults to (DD/MoMo/YY HH:MM. The 
other format is MoMo/DD/YY HH:MM. Use arrow keys to select desired format and 
press ENTER to accept. 

Instrument Timeout (7) 

To save battery power the 615 will shutdown if no key is pressed after X minutes. Use 
arrow keys to adjust the time out from ) minutes to 120 minutes. Press ENTER to accept. 
If the operator does not require this function set the time out to zero minutes. 

Set file in (8) 

Saved display and sensor parameter format can be saved for later retrieval and allows 
the current operator to have continuity in display and data format. 

Содержание 615

















































Отзывы:

Нет отзывов