Yenista Optics OSICS Скачать руководство пользователя страница 167

Страница: 167 / 252

Using the OSICS SWT APC Module

OSICS User Manual

167

12.10 Configuring the Modulation for All Connected T100 and

ECL Modules (Full-Band Mode)

Subject

The modulation is a typical function of OSICS T100 and ECL modules. For more details on

the modulation of these modules, see section

Using the OSICS T100 Module, p. 173

and

section

Using the OSICS ECL Module, p. 99

From the OSICS SWT APC, you can configure the modulation for all connected T100 and

ECL modules:

•

To define the modulation source for all connected T100 and ECL modules, see section

Defining the Modulation Source for All Connected T100 and ECL Modules, p. 167

•

To control the modulation of all connected T100 and ECL modules, see section

Controlling the Modulation of All Connected T100 and ECL Modules, p. 168

Before Starting

•

Set the SWT APC to

Full-Band

mode (see section

Selecting the Operating Mode,

p. 154

) and specify the connected modules (section

Configuring the Full-Band Mode,

p. 156

12.10.1 Defining the Modulation Source for All Connected T100 and ECL

Modules

Subject

The following section explains how to configure the wanted modulation source for all

T100 and ECL modules connected to the OSICS SWT APC.
The SWT APC has no internal modulation source, so if you set the modulation source to

INTERNAL, the internal modulation source of the corresponding T100 or ECL module will

be used for modulation.

Procedure

Access the SWT APC

Unit Setup

menu (see section

Accessing an OSICS Module Setup

Menu, p. 33

Expand the

Modulation

menu and enter the

Source

sub-menu.

The

Modulation Source

sub-menu appears and displays the current selected

modulation source.

Figure 123: SWT APC Unit Setup – Modulation Source

Turn the rotary knob to put the cursor before the wanted modulation source and

press it to validate your selection.

Main

EXIT

Unit Setup - Modulation source

ESCAPE

▲

Modulation source :

INTERNAL
MAINFRAME

Select a new value.

Содержание OSICS





























































































































































































































































Результаты поиска

Содержание OSICS

Отзывы:

Бренды по названию

Популярные бренды

Yenista Optics OSICS, Руководство пользователя

Результаты поиска

Содержание OSICS

Отзывы:

Бренды по названию

Популярные бренды