yellow jacket BJ-830008 Скачать руководство пользователя страница 7

Страница: 7 / 16

SYSTEM AIR PURGE PROCEDURE

IMPORTANT: BEFORE FIRST USE

Perform the following Air Purge Procedure to remove any air that may have been introduced into the hydraulic

system as a result of product shipment and handling. This step is to be completed without any weight on the

jack.

2. Turn release valve counter-clockwise on full turn

to the open position.

4. With a flat blade screwdriver, unscrew the oil fill

plug slightly to purge trapped air from system. (For

RUBBER OIL PLUGS Use caution not to tear or

puncture the oil plug.)

3. Rapidly pump the handle 6-8 times. Leave handle

in down position to expose oil fill plug.

6. Turn release valve clockwise to the closed

position.

7. Jack is now ready for use. Check for proper pump

action. (Repeat steps if neccessary).

Cover plate

1. Remove cover plate.

5. Replace Cover Plate.

Содержание BJ-830008

















Результаты поиска

Содержание BJ-830008

Отзывы:

Похожие инструкции для BJ-830008

Бренды по названию

Популярные бренды

yellow jacket BJ-830008, Руководство пользователя

Результаты поиска

Содержание BJ-830008

Отзывы:

Похожие инструкции для BJ-830008

Бренды по названию

Популярные бренды