Yealink VC110 Скачать руководство пользователя страница 156 | Manualshive

Страница: 156 / 268

background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint

144

Parameter

Description

Configuration Method

Default: Yealink VC110

To configure the site name via web user interface:

1.

Click on Setting->General.

2.

Edit the site name in the Site Name field.

3.

Click Confirm to accept the change.

The LCD screen of the display device and video conferencing phone will display
the changed site name.

To configure the site name via the remote control:

1.

Select Menu->Basic.

2.

Edit the site name in the Site Name field.

3.

Press the Save soft key to accept the change.

The LCD screen of the display device and video conferencing phone will display
the changed site name.

Backlight determines the brightness of the LCD screen display, allowing users to read
easily in dark environments. Backlight time specifies the delay time to turn off the
backlight when the phone is inactive.

You can configure the backlight time as one of the following types:



Always On: Backlight is turned on permanently.



15 s, 30 s, 10 min, 20 min, 30 min, 1 Hour, 2 Hour, 3 Hour, 4 Hour:

Backlight is turned

off when the phone is inactive after a preset period of time. It is automatically
turned on if the status of the phone changes or any key is pressed.

«
...
154
155
156
157
158
...
»

Содержание VC110













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VC110

Бренд: N-Com Страницы: 2

Бренд: Cyrus Страницы: 6

Бренд: Velux Страницы: 11

Бренд: WEST Страницы: 2

Бренд: HEIDENHAIN Страницы: 64

Бренд: YA Страницы: 2

Бренд: KBSOUND Страницы: 2

Enado Mini ENA-MINI-010

Бренд: Wyrestorm Страницы: 2

Бренд: DAPAudio Страницы: 17

Бренд: Jacuzzi Страницы: 28

Auto Sentry Petro

Бренд: ICS Страницы: 42

Lumina LU20S-DNW

Бренд: Leviton Страницы: 3

Leasam BM2-7D-4Z

Бренд: ActronControls Страницы: 2

Бренд: Roger Technology Страницы: 8

Бренд: Sharp Страницы: 16

Бренд: Sharp Страницы: 48

Бренд: Sharp Страницы: 44

Бренд: Sharp Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды