background image

 

 

EtherLeap User’s Manual 

LIMITED WARRANTY 

YDI Wireless (YDI) warrants that your device is free of defects in material and 
workmanship for a period of one year after initial purchase.  YDI will, in this period of time, 
repair or replace, any YDI product returned to the factory, freight prepaid. 
 
The YDI warranty covers repairs or replacement (at YDI’s option) of the product only.  YDI 
is not responsible for the cost of removal, reinstallation, or shipping to the place of repair.  
YDI does not extend or modify its warranty period as a result of repair or replacement. 
 
YDI reserves the right to void a warranty and/or make reasonable charges for repair of a 
unit if the warranty seal is broken or the unit displays evidence of misuse, abuse, or 
tampering. 
 
YDI is not responsible for damage to any other equipment or property, or any other 
consequential or incidental damages of any kind, whether based on contract, negligence, 
or strict liability.  Maximum liability shall not in any case exceed the purchase price of the 
unit. 
 
Warranties give you (the buyer) specific legal rights.  You may also have other rights that 
vary from state to state.  This warranty is only extended to purchases made in the United 
States of America or its possessions.

 

 

SPECIAL WARRANTY NOTICE 

The warranty is null and void if any of the following occurs: 

1.  The product enclosure is opened. 
2.  The connections are not properly waterproofed. 
3.  The device is installed improperly or with incorrect connectors. 
4.  The round connector of the outdoor Ethernet cable provided is improperly plugged 

into the rear jack of the enclosure. 

5.  The device or DC Power Injector are physically damaged. 
6.  The device is operated outside the recommended DC power specifications. 
7.  The device is damaged by extreme forces of nature, lightning, or ‘Acts of God.’ 

 

FCC NOTICE 

This device complies with part 15 of the FCC rules.  Operation is subject to the following two 
conditions: 

1.  This device may not cause harmful interference, and 

2.  This device must accept any interference received, including interference that may cause 

undesired operation. 

* Note:  The manufacturer is not responsible for any radio or TV interference caused by 

unauthorized modifications to this equipment.  Such modifications could void the user's 
authority to operate the equipment. 

These products are labeled with one of the following FCC ID numbers: 

 

FCC ID: NM5-EL24A-11  

Version 1.0 

Page i 

May 2003 

Содержание EtherLeap













Отзывы: