YATO YT-82854, Оригинальное руководство пользователя

Страница: 11 / 68

11
O R I G I N A L I N S T R U C T I O N S
GB
Safety recommendations for battery loading
Attention! Before loading may start make sure the body of the charger, the cable and the plug are not broken or damaged. It is prohibited to use a damaged
loading dock and charger! For the purpose of loading batteries only the charging dock and the charger provided may be used. Using another charger may
be a cause of fi re or damage the tool. Batteries may be charged only in a dry room, protected from unauthorised persons, particularly children. Do not use
the charging dock and the charger without permanent supervision of an adult! If it is necessary to leave the room where loading is taking place, it is required
to disconnect the charger from the mains, removing the charger from the mains socket. In case when smoke comes out of the charger, or a strange smell is
emitted, etc., it is required to immediately remove the plug of the charger from the mains socket!
The drill and automatic return screwdriver is provided with an unloaded battery, so before work may commence, it is required to charge it following the proce-
dure below, using the charger and charging dock provided. Li-ION batteries do not show the so called “memory e ff ect”, so it is allowed to charge them at any
moment. However, it is recommended to discharge them during normal work, and then load them to their full capacity. If due to the nature of the task it is not
possible to do so each time, then it is required to do it at least from time to time. Under no circumstances is it allowed to discharge the batteries short-circuiting
the electrodes, since this would cause irreversible damage! It is also prohibited to check the load of the batteries, short-circuiting the electrodes for sparking.
Storage of the battery
In order to prolong the life of the battery, it is required to provide adequate storage conditions. The batteries can go through approximately 500 „loading -
discharging” cycles. The battery must be stored between 0 and 30°C, at the relative humidity of 50%. In order to store the battery for a prolonged period, it
is required to charge it to approximately 70% of its capacity. In case of prolonged storage, it is required to recharge the battery once a year. Do not permit
excessive discharging of the battery, since this would reduce its life and may cause irreversible damage.
During storage, the battery will be gradually unloading due to leakage conductance. The process of automatic unloading depends on the temperature of
storage, since the higher the temperature, the fastest the process. In case of incorrect storage of batteries, there is a danger of electrolyte leakage. In case
of leakage, it is required protect the leakage with neutralizing agent. In case of contact of electrolyte with the eyes, it is required to rinse the eyes abundantly,
and then immediately seek medical assistance. It is prohibited to use a tool with a damaged battery.
In case the battery is completely worn out, it is required to deposit it at a special point dedicated to disposal of such waste.
Transport of the batteries
Lithium-ion batteries are in accordance with legal regulations treated as dangerous waste. The user of the tool may transport the tool with the battery or only
batteries by land. Then no additional conditions must be complied with. In transport is realised by third parties (for example dispatch through courier service),
then it is required to proceed in accordance with regulations for transport of dangerous materials. Before shipment, contact an authorised person.
It is prohibited to transport damaged batteries. During transport the battery must be removed from the tool, and the exposed contacts protected, e.g. with
insulating tape. Protect the batteries so that they do not move inside the package during transport. It is also required comply with the national regulations for
transport of dangerous materials.
Charging the battery
Attention! Before charging you should disconnect the charger from the mains by unplugging the power supply plug from the mains. In addition, you should
clean the battery and its terminals of dirt and dust with a soft, dry cloth.
The battery has a built-in charge indicator. When you press the button, LEDs will light up (II), the more LEDs will light up, the more fully the battery pack is
charged. If the button is pressed and the LEDs are o ff it means that the battery is discharged.
Disconnect the battery from the tool.
Push the battery in the charger socket (II).
Plug the charger into a mains socket.
When the red LED lights up, it means the loading process.
When charging is complete, the red LED goes o ff , and green LED lights up, indicating a full charge of the battery.
Unplug the charger from the mains outlet.
Remove the battery from the charging station, by pressing the battery latch button.
Attention! If, when the charger is connected to the power supply, the green LED is on, this indicates a fully charged battery. In this case, the charger does
not start charging.
WORKING WITH PRODUCT
Note! It is recommended prior to normal operation to make a test on waste material.
Insert the adhesive cartridge as far as it will go into the gun’s feed opening. Do not use excessive force for this (II).
Pressing the trigger only activates the mechanism feeding the adhesive cartridge towards the discharge nozzle.
The gun should be started by pressing and holding the gun switch (IV) for approx. 3 seconds. The nozzle backlighting lamp and the power indicator light next
to the switch will come on. The red indicator light indicates the heating process, green indicates readiness for work.
Point the gun nozzle in the place of the adhesive application (V), press the trigger, the melted adhesive will start fl owing out of the gun nozzle. Subsequent
pressing of the trigger will cause subsequent portions of glue to fl ow out of the gun nozzle.
Apply glue to the glued surfaces, press them together and wait. After approx. 1-2 minutes the connection is ready.