YATO YT-82854, Оригинальное руководство пользователя

Страница: 10 / 68

10
O R I G I N A L I N S T R U C T I O N S
GB
the mains socket. Avoid contact of the power supply cable with heat, oils, sharp tools and moving elements. Damage to the power supply cable
increases the risk of an electric shock.
In case work is realised outside closed areas, it is necessary to use extension cords designed for applications outside closed areas. Using a correct
extension cord permits to reduce the risk of an electric shock.
If operating a power tool in a damp location is unavoidable, use a residual current device (RDC) protected supply. Use of an RCD reduces the risk
of electric shock.
Personal safety
Commence work in good physical and psychological conditions. Pay attention to what you do. Do not work if you are tired or under e ff ects of
medicines or alcohol. Even a moment’s inattention during work may lead to serious injuries.
Always use individual means of protection. Always wear goggles. Using individual means of protection, such as dust-masks, protective shoes, helmets
and hearing protections permits to reduce the risk of serious injuries.
Avoid accidental activation of the tool. Make sure the switch is in the OFF position, before you connect the tool to the mains. Holding the tool with
a fi nger on the switch or connecting an electric tool when the switch is in the ON position may lead to serious injuries.
Before you turn an electric tool on remove all the spanners and other tools, which have been used for adjustments. A spanner left on rotating ele-
ments of the tool may lead to serious injuries.
Keep your balance. Maintain an appropriate position. It will permit to control the electric tool in case of unpredicted situations during its operation.
Use protective clothes. Do not wear loose clothes or jewellery. Keep your hair, clothes and gloves away from moving elements of the electric tool.
Loose clothes, jewellery or long hair may get caught on moving elements of the tool.
Use dust extractors or dust containers, if the tool is equipped with any. Make sure they are properly connected. Using of dust extractors permits to
reduce the risk of serious injuries.
Caution when using a power tool.
Before inserting a battery pack make sure that the switch stays in “OFF” position. Inserting a battery pack into a power tool, when the switch is in “ON”
position may cause accidents.
Use only chargers recommended by the manufacturer. Using a charger designed for only one type of battery pack, to charge other types of battery pack
may be a cause of fi re.
Use power tools only with battery pack speci fi ed by the manufacturer. Use of other battery pack may be a cause of injuries or fi re.
When the battery pack is not used, it should be stored away from metal objects, such as paper clips, coins, nails, bolts or other small metal ele-
ments, that may short the terminals. Shorting terminals of a battery may cause burns or fi re.
In adverse conditions, a liquid may escape from a battery; avoid any contact with this liquid. In case of accidental contact with a liquid, rinse with
water. If a liquid gets into your eyes, please seek medical advice. A liquid escaping from a battery may cause irritations or burns.
Repairs
The tool may be repaired only by authorised service centres, which must use solely original spare parts. It will guarantee a proper level of safety of
operation of the electric tool.
SPECIAL SAFETY CONDITIONS
Glue to be used only in form of a cartridge of diameter speci fi ed in the table with technical data.
The maximum operating time speci fi ed in the table with technical data applies to appliance with battery fully charged.
Since the glue gun operates at high temperature, special care should be taken during work.
During brakes and after completion of work the gun should stay in vertical position. Do not put the gun aside during work or place it in such position that the
glue outlet is directed upwards. Such position of gun may result in irreversible damage.
If brake in work lasts more than 30 minutes, wait a moment so that the cold glue cartridge could heat up.
Under no circumstances you may slide in the cartridge by force, the excessive pressure put on the cartridge may lead to glue cartridge being jammed inside
the gun. If the cartridge is jammed inside the gun, heat the gun for 10 minutes and then carefully remove the cartridge. If the cartridge is jammed deep inside
the gun, then heat up the new cartridge by applying it to gun outlet, apply the melted cartridge tip to glue cartridge that blocks the gun and after a while pull
o ff the whole by turning it slowly.
In no case it is allowed to clean the glue line with sharp tools.
A device must not be operated by children below 8 years of age and by persons with limited physical, sensor and mental capacity or persons with no experi-
ence and knowledge, if they stay under supervision or have been instructed how to use it safely and information about existing risk.
PREPARATION TO WORK
Note! All operations described in this chapter should be carried out with power supply o ff . Make sure, that the switch remains in “OFF” position - power
indicator does not light.