YATO YT-82281, Руководство пользователя

Страница: 11 / 72

11
GB
O R I G I N A L I N S T R U C T I O N S
Installation and replacement of the blade (II)
Make sure the installed blade is not damaged or broken, and the cutting teeth are not broken, etc. In case any damage is detected,
it is required to replace the blade with a new one.
The blade for wood and wood derivatives has wider spaced teeth, and the blade for metal and plastics has smaller teeth. Select
an adequate blade for the planned work. The blade must be installed with the teeth directed towards the lower part of the housing.
Attention! Installation of the blade must be realised wearing protective gloves, which will reduce the risk of injuries.
Turn the clamp of the spindle and insert the fi xture of the blade into the slot of the spindle. Turn the clamp in the opposite direction
and make sure the blade has been installed properly: the clamp has returned to the original position and the blade cannot be
removed from the spindle.
Adjustments of the height and the angle of the foot (III)
By means of adjustments of the height of the foot, the cutting height may be set. To do this, loosen the two screws at the bottom
of the housing, then set the foot to the desired height and tighten both screws. Make sure your foot does not change height during
operation. The foot permits continuous adjustments of the angle of the skid, and to do so, it should be inclined in relations to the
foot guide. This permits to adjust the cutting angle, without lifting the foot from the surface of the material being cut.
USING THE TOOL
Before work make sure the protection of the blade is installed correctly and lowered. Wear eye and hearing protection, as well as
protective gloves. Fix the object to be cut to the work station, using clamps or an anvil, etc. Do not ever keep the material being
cut in your hands or other parts of the body. In case of cutting, support the material at its edges and close to the cutting line. Place
the supports at both sides of the cutting line, so that during cutting the blade is not seized in the kerf. During cutting the base
must be placed with the whole surface against the material being cut. Connect the dust extraction system to the connection point.
Turning the reciprocating saw on and o ff
Make sure the surface at the place of work is even, stable and free from dirt.
Adopt a secure and stable position.
Hold the tool by the handle. Do not support the tool on any object.
Press the switch with a fi nger and hold it. Make sure the blade moves freely and the tool does not vibrate excessively and does
not emit smoke or a suspicious smell. In case and irregularity is observed, turn the saw o ff , disconnect the plug from the mains
and have the tool repaired at an authorised service point.
The switch is equipped with a lock, which may be used during long cutting. When the switch is pressed down, press the lock button
and release the switch. The lock is released when the switch is pushed down.
The tool is turned o ff when it is unlocked and the switch is released. Once the tool has been turned o ff , the blade keeps moving
for a while.
Cutting of wood (IV)
Before you proceed to cutting wood, use a woodwork pencil to draw the cutting line. Then place the tool on the foot and place
the blade in accordance with the line, and turn the tool on, wait until it has reached the nominal rotation and start cutting. During
cutting do not exert excessive pressure against the foot and the blade, since this might break the inserted tool.
In case of cutting wood, start cutting at a lower rotation and increase it during cutting.
Deep cutting
Attention! Deep cutting may be realised only in case of soft materials, such as soft wood or plasterboards. Do not ever realise
deep cutting in metal or another hard material.
In case of deep cutting, use a short blade. Set the maximum rotation. Place the edge of the foot on the material to be cut and
turn the tool on. Pressing the button, let the blade penetrate the material until the foot completely rests on the material being cut.
Continue cutting along the marked line.
Cutting at the edge
Attention! While cutting at the edge, use a special blade of high fl exibility.
It is possible to cut directly at the walls, fl oors and in other places which are di ffi cult to reach, e.g. while cutting pipes o ff . During
cutting, make sure the blade is continuously going through the full section of the material being cut. Cutting around the wall, which
may cause the tool to rebound towards the operator.
It is recommended to install a blade which is turned by 180 grades as related to the normal position. This will make the cutting
easier.
Cutting ori fi ces
Attention! For the purpose of cutting ori fi ces, use the blades for cutting arcs.
Before you start work, draw the cutting line. Drill a hole, insert the blade and start cutting.