YATO YT-82280, Руководство пользователя

Страница: 14 / 60

14
GB
O R I G I N A L I N S T R U C T I O N S
Cutting of wood (VI)
Before you proceed to cutting wood, use a woodwork pencil to draw the cutting line. Then place the tool on the foot and place
the blade in accordance with the line, and turn the tool on, wait until it has reached the nominal rotation and start cutting. During
cutting do not exert excessive pressure against the foot and the blade, since this might break the inserted tool.
In case of cutting wood, start cutting at a lower rotation and increase it during cutting.
Deep cutting
Attention! Deep cutting may be realised only in case of soft materials, such as soft wood or plasterboards. Do not ever realise
deep cutting in metal or another hard material.
In case of deep cutting, use a short blade. Set the maximum rotation. Place the edge of the foot on the material to be cut and
turn the tool on. Pressing the button, let the blade penetrate the material until the foot completely rests on the material being cut.
Continue cutting along the marked line.
Cutting at the edge
Attention! While cutting at the edge, use a special blade of high flexibility.
It is possible to cut directly at the walls, floors and in other places which are difficult to reach, e.g. while cutting pipes off. During
cutting, make sure the blade is continuously going through the full section of the material being cut. Cutting around the wall, which
may cause the tool to rebound towards the operator.
It is recommended to install a blade which is turned by 180 grades as related to the normal position. This will make the cutting
easier.
Cutting orifices
Attention! For the purpose of cutting orifices, use the blades for cutting arcs.
Before you start work, draw the cutting line. Drill a hole, insert the blade and start cutting.
Cutting metal
Attention! Select an adequate blade for the metal to be cut. This will increase safety and prolong the life of the blade.
In case of cutting of thinner sheet metal, place it between two pieces of wood. This will permit to obtain a smooth cutting line and
reduce the vibration generated during work.
It is recommended to use an adequate cooling agent for the given metal. If possible, spread a thin oil film within the area of opera-
tion of the foot of the saw. This will make operation of the saw easier.
Additional remarks
Avoid overloading the tool – the temperature of the external surfaces must not exceed 60oC.
Once the task has been concluded, turn the saw off, remove the plug of the tool from the mains socket and inspect the machine.
The declared total value of vibration has been determined by means of a standard measurement method and may be used to
compare the tool with another one. The declared total value of vibration may be used for an initial evaluation of exposure.
Attention! The vibration caused during work with the tool may differ from the declared value, depending on the way in which the
tool is used.
Attention! It is required to determine safety measures to protect the operator, based on evaluation of exposure under actual
circumstances of operation of the machine (including all the phases of the working cycle, for example the time when the tool is off
or is idling, and the activation time.
MAINTENANCE AND OVERHAUL
ATTENTION! Before any adjustment, technical service or maintenance operations unplug the tool. Once the operations have been
finished, the technical conditions of the tool must be assessed by means of external evaluation and inspection of the following
elements: body and handle, conductor with a plug and deflection, functioning of the electric switch, patency of ventilation slots,
sparking of brushes, noise level of functioning of bearings and gears, start-up and smoothness of operation. During the guarantee
period, the user cannot dismantle the electric tools or change any sub-assemblies or elements, since it will cancel any guarantee
rights. All irregularities detected at overhaul or during functioning of the tools are a signal to have the tool repaired at a service
shop. Once the functioning has been concluded, the casing, ventilation slots, switches, additional handle and protections must be
cleansed with a stream of air (at a pressure not exceeding 0.3 MPa), with a brush or a cloth without any chemical substances or
cleaning liquids. Tools and handles must be cleansed with a clean cloth.