11
O R I G I N A L I N S T R U C T I O N S
GB
If operating a power tool in a damp location is unavoidable, use a residual current device (RDC) protected supply.
Use of
an RCD reduces the risk of electric shock.
Personal safety
Commence work in good physical and psychological conditions. Pay attention to what you do. Do not work if you are
tired or under e
ff
ects of medicines or alcohol.
Even a moment’s inattention during work may lead to serious injuries.
Always use individual means of protection. Always wear goggles.
Using individual means of protection, such as dust-masks,
protective shoes, helmets and hearing protections permits to reduce the risk of serious injuries.
Avoid accidental activation of the tool. Make sure the switch is in the OFF position, before you connect the tool to the
mains.
Holding the tool with a
fi
nger on the switch or connecting an electric tool when the switch is in the ON position may lead
to serious injuries.
Before you turn an electric tool on remove all the spanners and other tools, which have been used for adjustments.
A
spanner left on rotating elements of the tool may lead to serious injuries.
Keep your balance. Maintain an appropriate position.
It will permit to control the electric tool in case of unpredicted situations
during its operation.
Use protective clothes. Do not wear loose clothes or jewellery. Keep your hair, clothes and gloves away from moving
elements of the electric tool.
Loose clothes, jewellery or long hair may get caught on moving elements of the tool.
Use dust extractors or dust containers, if the tool is equipped with any. Make sure they are properly connected.
Using of
dust extractors permits to reduce the risk of serious injuries.
Operation of the electric tool
Before the battery is installed, make sure the switch is o
ff
. Installation of the battery when the switch is on may lead to accidents.
Use solely the charger recommended by the manufacturer. Using a charger designed for another type of battery may be a cause
of
fi
re.
The electric tool must be operated exclusively with the battery indicated by the manufacturer. Using another battery may be a
cause of
fi
re or injuries.
When the battery is not used, it must be stored away from such metal objects as paper clips, coins, nails, screws or other small
metal elements, which might short-circuit the terminals
.
Short-circuited terminals of the battery may cause burns or
fi
re.
Under adverse circumstances liquid may leak from the battery; avoid any contact. In case of accidental contact with the liquid,
rinse it with water. In case of eye contact, seek medical. The liquid leaking from the battery may cause irritation or burns.
During work when the tool may touch a hidden live conductor, the electric tool must be held by insulated handles. The installed bit
in case of contact with a live conductor may conduct electricity to the metal elements of the tool, which may cause electric shock
to the operator.
Repairs
The tool may be repaired only by authorised service centres, which must use solely original spare parts.
It will guarantee
a proper level of safety of operation of the electric tool.
ADDITIONAL SAFETY INSTRUCTIONS
Safety warnings for straight grinders
The tool is designed only for grinding with grinding pins, wire brushes with the spindle, and polishing. Read and view
all warnings, instructions,
fi
gures, and speci
fi
cations supplied with the power tool.
Failure to follow all of the instructions
provided below may result in electrocution,
fi
re, and / or serious injury.
It is not recommended to perform works such as cutting or grinding with sandpaper with this type of tool.
Performing
other works than for which the tool is intended may pose a risk and result in injuries.
Do not use accessories which have not been designed by the manufacturer or intended for the work with the tool.
A
possibility of mounting accessories on the tool does not ensure safe operation.
The maximum rotational speed of the accessories must be equal to or greater than the maximum rotational speed of the
tool.
Accessories with a lower rotational speed than the tool speed can disintegrate during operation.
The outer diameter and thickness of accessories must be within the size range speci
fi
ed for the tool.
It is not possible to properly guard or operate improperly sized accessories.
The size of the hole used for
fi
xing wheels, discs,
fl
anges, and other accessories must match the size of the tool spindle.
Accessories with a
fi
xing hole size not suitable for the tool spindle size will start to vibrate during operation, which may result in
the loss of control of the tool.
Do not use damaged cutting discs. Before each use, check the discs for cracks and splinters. If the power tool or disc
has been dropped, check them for damage or assemble undamaged discs. After inspection, leave and remove bystand-
ers from cutting disc rotation plane and then turn on the power tool for one minute at maximum speed.
Damaged cutting
discs will break during this test.
Wear personal protective equipment. Use face shields, goggles, or safety goggles, depending on the application. If re-
quired, use dust masks, hearing protection, safety gloves, and aprons to protect against small pieces of accessories or
Содержание YT-82080
Страница 95: ...I N S T R U K C J A O R Y G I N A L N A 95 ...
Страница 96: ...I N S T R U K C J A O R Y G I N A L N A 96 ...
