8
O R I G I N A L I N S T R U C T I O N S
GB
PRODUCT CHARACTERISTICS
The fryer is designed for frying French fries in cooking oil. The product can be used to prepare French fries from both fresh po-
tatoes and frozen fries. In addition to French fries, the product can be used to prepare other dishes from potatoes intended for
deep-fat frying. Thanks to adjusting the operating temperature, the product can be adapted to your own needs. Correct, reliable
and safe operation of the product depends on proper operation, therefore:
Before starting product operation, please read this manual and keep it.
The supplier does not assume any liability for any damages resulting from misuse of the product, failure to follow safety regu-
lations and recommendations specifi ed in this manual. Misuse of the product will also result in loss of guarantee and warranty
rights of the user.
EQUIPMENT
The product is delivered complete and does not require assembly. Therefore, before using the product, it is required to remove all pack-
ing and protection elements for transportation. Some preparatory actions described in the further part of this manual are also required.
GENERAL USE RECOMMENDATIONS
Product is designed for professional use and should be operated by properly qualifi ed personnel.
NOTE!
Do not use the fryer to fry potato products that contain liquid or semi-liquid fi lling, e.g. cheese. The fi lling may fl ow out
during the frying and sink at the bottom of the fryer chamber, where it will be burnt, which may lead to product damage.
NOTE!
Do not open the drain tap while the product is under operation.
Unattended repair, disassembly or modifi cation of product is forbidden. All product repairs must be carried out by an authorised
repair point.
Product should be supervised all the time when operating.
WARNING!
During operation the product heats up to high temperature, do not touch the walls of product during operation, it can
cause serious burns.
This product is not intended for use by children below 8 years of age and persons with reduced physical or mental capabilities
and person with no experience or knowledge of the equipment. Unless they are supervised or trained how to use the product in a
safe manner so that the risks involved are understood. Children should not play with the product. Unattended children should not
perform cleaning and maintenance of the equipment.
Recommendations for the product transportation and installation
NOTE!
Product installation and connecting can be done only by qualifi ed personnel.
Product can be placed only on a hard, fl at, level and non-fl ammable surface. Substrate should withstand the weight of appliance
itself together with foodstuff s put inside.
Provide at least 10 cm space around product’s side walls, do not place any materials not resistant to high temperature above the
product. This will allow proper product ventilation. Do not place the product near edges e.g. of a table.
Do not place any electrical appliances over the product. Water steam is released during operation of product, which may cause a
short circuit of the electrical installation resulting in electric shock.
It is forbidden to drill any hole in the product, nor any other product modifi cation not described herein.
Product to be carried when cooled, by gripping its housing. Do not displace the product by pulling the cable cord.
Do not place any metal objects and surfaces behind the product or in its vicinity.
Do not place the product at places with high temperature. Temperature at the place of installation and use of product must stay
within the range +10
O
C ÷ +38
O
C and the relative humidity must be less than 90%, without steam condensation.
Recommendations for connecting the product to power supply
Before connecting the product to power supply, make sure that the voltage, frequency, and capacity of mains supply correspond
to values shown on the product nameplate. Plug must fi t into the socket. Any modifi cations of plug are forbidden.
The product must be connected directly to a single power outlet. It is forbidden to use extension cords, socket-outlet adapters and
double power outlets. Power supply circuit must be fi tted with a protective conductor and at least 16 A protection circuit.
Avoid any contact of power cord with sharp edges and hot objects and surfaces. When operating the product, the power cord
must always be fully unwound and its position may not interfere with the operation of product. Laying of power cable cannot result
in tripping hazard. Power outlet should be located in such a place to allow always the possibility of quick disconnecting the plug
of power cord supplying the product. When disconnecting the plug of power cord always pull the plug housing, never the cable.
If the power cord or plug is damaged, disconnect it immediately from the mains and contact an authorized manufacturer’s service
centre for replacement. Do not use the product with a damaged power cord or plug. Power cord or plug cannot be repaired, in
case of damage to these components, replace them with new ones without defects.
Do not touch the plug of power cord with moist or wet hands.