background image

 

TABLE OF CONTENTS

 

MOTO

 

MAN

i

Twin Drive Function Manual

 

Section

Page

 

1 INTRODUCTION 

1.1 

About this Document .................................................................................................... 1-1

1.2 

Reference to Other Documentation................................................................................ 1-1

1.3 

Customer Service Information....................................................................................... 1-1

2 SAFETY

2.1 Introduction 

.................................................................................................................. 2-1

2.2 

Standard Conventions................................................................................................... 2-2

2.3 

General Safeguarding Tips............................................................................................ 2-4

2.4 

Mechanical Safety Devices............................................................................................ 2-4

2.5 Installation 

Safety.......................................................................................................... 2-5

2.6 

Programming Safety ..................................................................................................... 2-5

2.7 Operation 

Safety............................................................................................................ 2-6

2.8 

Maintenance Safety....................................................................................................... 2-7

TWIN DRIVE INSTRUCTIONS

Outline for Twin Drive Instructions................................................................................ 1-1

Applicable Stations............... ............................... ........................................................ 2-1

3

Operation ...................................................................................................................... 3-1

4

Setting Parameters........................................................................................................ 4-1

5

Status Display............................................................................................................... 5-1

6

Precautions................................................................................................................... 6-1

Содержание Motoman XRC





































Отзывы: