YASKAWA Motoman MH Series Скачать руководство пользователя страница 20

Страница: 20 / 116

EQUIPMENT DESCRIPTION

MH-Series Positioner Manual with MotoMount

3-2

MOTO

MAN

3.1.1

Type I Specifications

See Table 3-1 for Type I drive assembly specifications.

External axis default settings

Weld capacity is at 100% duty cycle.

*** The In-position Maximum Motion is the maximum motion expected if the

cycle start command is given while the safety zone is violated. This assumes
utilizing the position switches in the safety circuit, and includes the motion
required to clear the switch actuators and implement an E-Stop.

See Appendix A for drive series component performance charts.
See Section 4.2 for installation instructions.

Table 3-1 MH-series Type I Specifications

Series Component

MH75

MH150

MH450

MH1500

Motoman P/N

145878-1

145878-2

145881-1

146615-1

Axis Type

Rotation

Rated Load – kgf

150

450

1500

Rated MHT Load @ CG Off Center – kgf @ mm

550 @ 20

550 @ 40

1075 @ 60

3000 @ 70

Headstock Speed – rpm

24.7

12.4

9.8

10.6

180-Degree Sweep Time – sec

1.72

2.92

3.56

3.32

Rated CG Off Center – mm

152

Rated CG Overhang – mm

500

200

100

Load @ 500 mm CG Overhang – kgf

175

500

Rated Inertia – kg*m

119

680

Rated Holding Torque – Nm

112

224

671

2236

Rated Weld Current (Standard/Optional) – Amps

400/800

800/1200

800/1600

Allowable Thrust – kgf

400

800

2000

Motor Power – kW

0.60

1.3

4.5

Motor P/N, YEC

SGMDH-06A2A-YR13

SGMGH-

13A2A-

YR13

SGMDH-

45A2B-

YR14

Motor Speed – rpm

2000

1500

Rated Acceleration – sec

0.3

0.5

Motor P/N, Motoman

142182-2

142142-4

142142-1

Reducer

RV-20E-

81-1B

RV-20E-

161-1B

RV-80E-

153-1B

RV-320E-

141

Total Reduction Ratio – R

161

153

141

Repeatability – mm/mm

0.00003

0.00004

0.00003

0.00002

Repeatability w/MotoMount – mm/mm

0.00005

0.0002

0.0001

E-Stop Response – sec

0.15

0.14

0.2

E-Stop Response – deg

*** In-position Maximum Motion – deg

Face Plate Through Hole

none

Tail Stock Through Hole Dia. – mm

Drive Assy Weight – kgf/lbs

54/118

100/220

390/860

Standard Tool Radius – mm

815

1000

Содержание Motoman MH Series





















































































































Результаты поиска

Содержание Motoman MH Series

Отзывы:

Похожие инструкции для Motoman MH Series

Бренды по названию

Популярные бренды

YASKAWA Motoman MH Series, Руководство пользователя

Результаты поиска

Содержание Motoman MH Series

Отзывы:

Похожие инструкции для Motoman MH Series

Бренды по названию

Популярные бренды